NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hi,
We had developped a new product using NR52840 and also the nRF5 SDK v17.0.2.
We would like to use the DFU of Nordic instaed of developping our bootloader.
We will...
Dear All
I have just done and project and would like to modify it into a different application aiming to save some time, I copied & pasted the whole project and renamed...
I saw this library for Android development.
Is there a library for iOS development for nRF connect Device Manager?
Or any other tool to allow OTA DFU iOS, compatible with...
Hi,
we have a custom board with nrf52840 and nrf9160. NRF9160 has mfw_nrf9160_1.3.3 and serial_lte_modem application. I try to set modem system mode to support both LTE...
Hello,
I'm developing Zigbee End Device based on nRF52840 and I have some problems with network joining.
If my device is close enough to coordinator(1-1.5m) than it joins...
Hi,
I am trying to operate the sparkfun triad spectral sensor using an nRF5340 DK and the nRF SDK v.2.2.0 via I2C.
I did find an Arduino Library for to work the sensor...
I am working on a wearable device and using NRF5340 SoC. I am confused about Bluetooth communication. Do I have to use external antenna for Bluetooth data transmission or...
I'm trying to understand how the selection mechanism of Bluetooth LE controller (SoftDevice vs Zephyr) works in nRF Connect SDK samples.
The documentation clearly states...
Hello, I am developing an On/Off Light Matter device, which has buttons onboard. Currently, I'd like to make it possible to 'unbound' buttons from controlling On/Off Light...
When I select "Open VS Code" a pop up window comes up with "Install nRF Command Line Tools".
I have installed nrf-command-line-tools-10.19.0-x64.exe. Even though I installed...
Hello Nordic Team,
I am working on an application which has custom bootloader and BLE application firmware. The bootloader code resides in flash area 0xE0000 - 0xEDFFF,...
hi,
can i allocate array in the flash in specific address?
i want to save communication time to the flash (I2C)
what i need to do to write to flash without spend time...
We are using:
NCS v1.9.1 nRF52840 openthread
We expect to operate in an environment with other Thread networks. So, we would like to randomize the network credentials...
Good morning, I'm developing a thermostat. I'm using the nRF5 SDK for thread and zigbee 4.2.0 - ZBOSS version 3.11 I have an issue with the cluster 0x201 attribute OccupiedHeatingSetpoint...
Hi, I'm currently using nRF9160DK as Evaluation board and the LTE Link Monitor works fine with 9160DK.
Uur goal is to use Fanstel LN60G/E module, which has nRF9160 SIP....
