NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hello,
We need to monitor signal quality on production devices to know in detail the quality of service or if we need to change antennas in some areas. For this i saw two...
Hello,
I trying to interface with a I2C device (specially, ST25DVxxK) that requires a specific I2C start sequence to ensure correct arbitration:
(from ST AN5624).
...
We are testing connection with our rohdes and schwarz (CMW290) devices in LTE with an NRF9160 and we have problems disconnecting with the device.
The modem connects and...
Hi,
I would like to document the error reason and program counter on every hard fault.
I added it to my application, in HardFault_c_handler (). I save p_stack->pc and...
Hi!
We have some legacy IoT devices currently running with s132 3.1.0 softdevice (yes... very old). We would like to push a major update of the fleet, with our latest firmware...
Hi, we encountered a problem with nRF_Connect SDK v2.2.0 that is not a problem with SDK v2.1.0.
We have a project running on the nRF5340 that requires using shared secrets...
Hi,
I am currently using a NRF52-DK board with a NRF52832. Measuring the power consumption I realized that at very low load, the internal power supply's mode of operation...
hello,
using nrf5340 with custom and been trying to adding interfaces like ic1,ic2 and uart
initially i have added this in my overlay files
& i2c1 {
compatible = ...
Hi,
I'm using NRF52840 DK as a debugger of NRF52840 Dongle. And I'm using Segger Studio with NRF SDK.
I used the P20 header in NRF52840 DK as interface to the Dongle....
In a research project we need to implement a bridge from a ZigBee network to a Matter ecosystem. Is there any example available to do such a thing? We found that there is...
Hi,
I am using an device with an nRF52810 as a peripheral and my Windows 10 PC with an nRF52840 Dongle as the central. I am using a QT Application that uses the pc-ble...
Hi everyone, I'm trying to create a ble app uart coexist example to nrf52840. However after I add everything like this thread and the existing example on nrf52832, I'm running...
Hi All,
We are using nrf52840 and SDK version 'SDK-15.3.0'. We have developed a network of nrf52840 (peripherals). We are using mobile Bluetooth to update the peripheral...
Dear,
I am using nRF5340 and I am trying to scan devices around me. With the example observer my device founds other devices around me, but when I use the same configuration...
I am checking the voltage of my NRF52833 DK and I am getting 2.9V in some of my GPIO pin. Adding to it I didn't feed any program to make that pin to High state. I want to...
