NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
i use the zephyr 3.0.9.i use direction with nrf52833 or nrf5340 in RX.The tx is nrf52833 with nrf of NCS,ITversion is zephyr 2.7.9.The default is 2us AOA. I want to use 1us...
Hi,
I have installed Segger Studio for ARM v6.22a.
I have also installed the SDK5 version 12.3.0.
I imported the IAR project project ble_app_start_notification_pca10028_s130...
Hello,
I have been working with a BLE custom board project for a few months and the product requires buttonless DFU feature. The bootloader that I initially used was derived...
System details:
Board: Custom
Chip: nRF52832
PCA Number: PCA10040
SoftDevice: S132
SDK: Version 16.0.0
I have been building a custom nRF52832 device for a...
I'm trying to use the LTE Link Monitor, but when I open the app, the log shows: Failed to get the library versions: JLINKARM_DLL_COULD_NOT_BE_OPENED (Origin: "Failed to get...
sdk: 1.6
modem fw: 1.2.3
Hi,
Been trying to test mqtt every which way and not getting any success with mqtt keep alive longer than 30 minutes, the mqtt connection...
Hi All,
I have encrypted app_update.bin manually and perform FOTA with single stage bootloader and it is working as expected.
Now I have enabled Two stage bootloader...
i am working with spi example but the clock appears as shown in the following photo i do not know why it is generated like this and i need help to configure it to work as...
Do you have an updated schematic for the latest nRF52-DK development board? The board I have from July 2022 (reference # 0365RUBR) has some differences compared to the online...
Hi there,
A couple of weeks ago, I'm facing the issue that my nRF52840DK board is not visible and led5 is flashing rapidly. I reflashed the bootloader, j-link-ob-sam3u128...
I added some functionality to asset_tracker_v2. I used two pins of Nordic chip for following purpose: 1. Detect BMS, pin as Input 2. Reset BMS, pin as output. The pins overlay...
Hi,
I'm a newbie of microwave board design, after many research I finished our 2.4G USB Receiver board which use the nRF52840-QIAA. But I still want some advice of the RF...
Hello,
My setup is UDP sample and PPK2 for power measurements. I am trying to figure out the best settings that are available with eDRX set to <= 20.48s, and preferably...
Hello,
I am trying to get the data out of an out of the box zigbee sensor (PIR motion sensor) with the CLI example provided.
I flash an NRF52 with the CLI example, and...
