Hello Nordic Support,
I am developing a cellular positioning solution using an nRF93M1 LTE Cat 1 bis module.
I currently use the following command to retrieve the serving...
Hi,
We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM.
We have already consulted with you regarding the design under Case ID...
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
I am using the SDK v3.4.0 LTS
for modem error debugging I included: prj.conf
I am mapping errors depending on wether memory allocations failed.
I am fetching the stats...
If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
Hi,
I am developing firmware on the nRF93M1 DK and have a question regarding the Wi-Fi location feature. According to the Nordic documentation (Features of nRF93M1 — nRF...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
Hello，
I am using ncs1.7.1, qspi + mx25r64 external flash ota it works well, but I don't know how to change qspi to spi.
I need your help thanks
I change the parament...
Hi Nordic,
I am working on a raspberry pi based gateway which has Thread Border Router and edge node functionality. I have setup the OTBR on the gateway and I have manage...
Hi,
how can I change the standard LED_0 output from P0.17 to P0.03? I am using SES, toolchain 1.8.0 and the nRF52DK board and I would like to flash the sample code to a...
Hello! I have WF200 wi-fi chip connected to the nrf52840 through SPI. I configured bare-metal example code of WF200 chip to work with nrf-sdk and this example (basic CGI server...
No connection after disconnect with Android App Nordic Uart Service until mac-address of smartphone changes
Multilink multirole software developed in SES studio.
Other...
Hi I have a product that uses an Nrf52810 in a Raytec slave module. I am able to successfully send and receive packets of data using your UART app in the nrf Toolbox
I would...
Hi,
1. I need to change the total free space of this file system: Current size:24576 bytes
3. I made the following adjustment, but it didn't work.
4. How do I modify...
nRF Connect for Desktop cannot find any devices from the SELECT DEVICE tab in LTE Link monitor or Bluetooth Low Energy app.
The device can be found on Device Manager and...
Hi, all.
I'm using nRF52833 and trying to communicate ESP8266 using UART.
I already successfully communicate with Dust Sensor with baudrate 9600, so I tried to communicate...
Hi,
I'm trying to find an example of using the I2S audio interface with the Zephyr RTOS on the nRF52840dk_nRF52840 development board or on an nRF52840 device in general...
Hello ! I'm a beginner here, and I have a problem that I struggle to solve. A few years ago, a firmware was done by a company, for the one I work for. It was done with IAR...
Hi,
I am toggling a GPIO using the below code and trying to find out the relation of the frequency and the code statements. I know that GPIO peripheral is running at 16MHz...
Hi,
after fixing a missing ground in my setup (see devzone.nordicsemi.com/.../interaction-jlink-and-power-profiler-ppkii) I have not been able to get less than 50uA of idle...
My B0n bootloader (running on the network core) is trying to access XIP space and faulting. This is a part of an network core upgrade.
From what I can learn from the data...
Good evening,
I’m testing the SDK v17.1.0 “Open Bootloader with DFU” example. I’m using Segger Embedded Studio to program my Nano 33 BLE via the debug interface (P20) of...
