Hello,
I am experiencing significant discrepancies when measuring current with a PPK2 in Ampere Meter mode using a Python API ( ppk2_api ) compared to the official Power...
Hello,
I want to program and debug a custom board using my nRF52840 DK (PCA10056 v3.0.3) as the programmer, through the Debug out connector P19. Before I order the cable...
Hi Nordic Team,
I'm debugging an unexpected software reset on an nRF54L15 running nRF Connect SDK v3.4.0 . BLE FOTA through MCUmgr completes successfully and the new image...
We are particularly interested in the following frequency ranges:
2400–2483.5 MHz
2483.5–2522 MHz
2522–2800 MHz
Higher out-of-band frequencies
Could you provide...
Dear Nordic,
We are testing an nRF9151 DK in a lab environment using an LTE callbox. We are testing a scenario in which the callbox is transmitting 6 cells on the same DL_EARFCN...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Hi Nordic Team,
My dev environment is as follow:
nRF52832(ble central)+ S132+ SES
We are using BLE Chip on a custom board.
When we flash hex file ( softdevice hex...
Hello,
I am currently evaluating whether the WiGLE geolocation interface is something that the nrf9160 can support.
One of the required pieces of information for that...
Hi,
I am using AFE4403 and Nrf52840, I want to assign a pin as output oscillator 4M using a nrf52 internal oscillator,
how to do that?
I am beginner , is my first...
Hi Everyone,
I'm not able to start ble scan. I've followed following example...
Developing Bluetooth Low Energy products using nRF Connect SDK
https://www.youtube.com...
Hello,
I was trying out sending RR intervals on the Heart Rate Measurement service and seeing what happens in nRF Connect. But, something is weird with the way the values...
I have a client project developed in 9160 which needs to be connected to the network via NB or LTE-M. Before each connection, I read imsi to determine the apn of the carrier...
Hi
Im trying to get the mcp2515 candriver example to work https://github.com/nrfconnect/sdk-zephyr/tree/main/samples/net/sockets/can#id3 .
i have some error during build...
We have an nRF52 with dual roles: peripheral for the connection to an app, and central, connecting to multiple third party peripheral devices.
We have come across a very...
Hello,
I'm using Segger Embedded Studio (SES) (on Windows 10) with nRfConnect SDK and nrf5340 processor.
In SES I can oben a graphical view of the configuration through...
Hi, I have developed a firmware on nRF52840 as central ble_app_uart_c\pca10056\s140. Now I have to upload it in nRF52810 which soft device should I use? Thanks!
Hi all,
I working with NCS v1.7.1 on a custom board using nRF52840 and I am trying to enable a 2-stage bootloader setup using NSIB as the first stage immutable bootloader...
Hello sir,
I am using the nrf52832 Dev board and try to send the data through custom value update then the following error occurs as ERROR 8 [NRF_ERROR_INVALID_STATE].How...
P0.25 is accessible by below:
nrf_gpio_pin_set(25);
However, when I try to access P1.00: Neither this:
nrf_gpio_pin_set(1); Nor this works:
nrf_gpio_pin_set(32);...
Hello, we have a device that uses the nRF9160 with an external GPS receiver that is controlled over I2C. I have connected the LNA enable pin to COEX0 on the nRF9160, but it...
