Excuse me.
When the customer uses the nPM1300 EK for battery charge‑discharge profile logging, after charging completes at 45 °C and the USB cable is unplugged as prompted...
Hi Nordic team,
I am following up on a previous thread ( nRF54L15 sQSPI support for SPI NAND in NCS v3.3.1 ) where it was confirmed that NAND flash was not supported in...
We have purchased a radio fitted with the nRF9160 modem and fitted it with a roaming SIM for NB-IoT use, we are in UK and have Band 20 EE and Vodafone.
What are the initial...
Hi
in conn_time_sync some thing must be broken. Central and peripheral connect to each other. The logs look as expected.
BUT:
THE LED's wont blink.
When I copy a sample...
My device uses the nRF52840. I migrated my Zigbee application from nRF Connect SDK v2.5.1 to the Zigbee R23 add-on v1.4.0.
After migrating to the R23 add-on, I noticed that...
Hello Nordic Semiconductor Support,
I would like to request an RMA/replacement for an nRF52840 DK (PCA10056) that appears to have a failure in the Interface MCU/USB debugger...
Hi, I am experiencing an issue where a specific nRF9151 SMA DK kit is stuck in an infinite network registration loop. The modem continuously reports +CEREG: 2 (Not registered...
Hello,
I'm using the NRF5 sdk v17.0.2 with s140 on the nrf52840,
I would like to know the technical reason why the APP_ERROR_HANDLER definition in app_error.h depends...
Hi
1、I according to the link below to change the project of nrf52833 to nrf52820，but failed!
Nordic Semiconductor Infocenter
2、Figures below are my modified in the...
Hello,
I am testing the 1 CENTRAL module with 4 PERIPHERAL module connection.
So I set the
NRF_SDH_BLE_CENTRAL_LINK_COUNT 4
NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 0 ...
Hi,
I have two custom boards, one is central with nRF52933 and other is peripheral with nRF52832.
In the previous test, the connection between the 52833 central board...
Hi Team
Because Ble_2Mbit have better RX sensitivity than Nrf_2Mbit. Can I use Ble_2Mbit in ESB code? Is there any potential technical or legal risk? thank you.
regards...
Before updating to V2.00, the DTM tool can automatically detect the serial port, log has a clear indication whether it is connected to the target board, when the DTM update...
Hello.The SDK version I'm using is 17.0.1 and the protocol stack version is S140_7.2.0. I use the nrfutil to generate the update zip file for dfu,but I find that the nrfutil...
Hello! I have the whitelist support for my device with the default settings:
My goal is to rewrite saved addresses in the whitelist, when there is a new 9th address bonded...
Hi,
I'm working on adding the buttonless DFU function to my application. It works fine when I disable NRF_PWR_MGMT_CONFIG_AUTO_SHUTDOWN_RETRY in sdk_config.h . However,...
Hi everyone.
I have a custom board with nRF52832. I am using J-Link for programming. In my custom board, SWD pins are exposed. So I can erase nRF52832 succesfully and programmed...
I have recently switched from development with the nRF52832 to the nRF52840 and along with this switched from the nRF52-DK to the nRF52840-DK. I am unable to connect to the...
Hi everyone,
I try to connect simulatanoues 12 BLE devices to a Linux PC with Bluez.
You cannot go above 5 with commercial BLE controller.
So I want to use the dongle...
As many others have found, and answered questions here and here and in other posts, DFU will prematurely exit IF you have enabled WDT in your application, as the current Nordic...
Dear Nordic Engineers
I recently encountered a problem when developing NRF9160.I developed it based on the example of asset_tracker_v2.Now I have an .a file of an encryption...
I am using SDK 15.2 with Segger Studio
I am using an external button on pin 4 to enter sleep mode on a long press and wake up the device.
I am able to enter sleep...
