Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
NCS: v3.4.0 Board: custom board based loosely on PAN1783 TF-M not used
Images: - App core: mcuboot, Firmware (main app) - Net core: b0n, ipc_radio
Summary of configuration...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I am investigating the data bit and stop bit settings. At that time, I found a page...
Hi !
I try to use VSCode but any examples return same error:
"Linking C executable zephyr\zephyr_prebuilt.elf FAILED: zephyr/zephyr_prebuilt.elf zephyr/zephyr_prebuilt...
Hi,
As the title states, VS code doesn't recognize includes related to Zephyr.
I've walked through the entire setup guide and installed all components using the toolchain...
So I came across an issue while working on developing an app that can update firmware OTA. I was using Nordic Semi - android DFU Library
implementation 'no.nordicsemi.android...
hi，
1.Now I am using Wireshark to capture nrF52840 DK ZigBee packets. I have configured the environment according to the guide. In wireshark, "nRF Sniffer for 802.15.4"...
hi，
we are using52833 QFN40 to test carrier,but the program will loop at as the picture bellow,while it runs well in 52833 QQFN73 in another board, why? Coutl you help me...
Hello,
Our modem consumes a lot of current when we use a simcard from a provider 1 (a MNO), much more that when we use a simcard from another provider 2 (a roaming service...
Hi,
with a custom hardware, I'm using a NRF9160 with a ESP8266 chip over uart with following prj.conf and board overlay:
I was trying to open a socket (that uses the...
Hi
The chip used is nrf52832, the SDK version is a peripheral device v13, and the central device uses v16.
The referenced example is ble_app_multirole_lesc and has been...
Background: SDK 16.0.0, SoftDevice 7.0.1, 1 ble_central connected 6 ble_peripheral, Send an instruction to 6 ble_peripherals every 50 milliseconds, at the same time, the ble_peripheral...
We need fast response from peripheral to central. That means we need a fast connection interval. We are using less than 100mS. But that results in an unacceptable battery...
Hi I have a question regarding USB port on the nrf52840 device When connecting a new device to computer is it possible to tell PC to assigne the same COM port number as last...
Hello, this is my first post in here. I'm trying to read the TX_POWER information of my beacons. I'm able to read this info using the nRFConnect app on my phone no problem...
