Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi Nordic Team,
I've read some forum discussion about using NAND SPI Flash Chip as external flash storage. These are two chips I'm considering :
W25N01GVZEIG ...
Hi,
We are currently trying to create a small test code to test multiple operator with different modes:
- lte-m1 or lte-nb1
- edrx 0s, 5.12s, 10.24s
- with and without...
Dear Nordic Team,
I recently ported the BLE UART example project for the PCA10056 to the PCA10059 dongle (SoftDevice 113). I added some minor changes like RX/TX pins, GPIO...
Hardware:
Raspberry Pi Zero W
nRF52840 DK running Serial Example and connected to RPi via USB
Custom nRF52840 board acting as a Vendor Model Server x 2
Software...
Hello,
I cannot find a download link for the 17.0.0_9d13099 build of the SDK. Is it publicly available and if not, can a private link be provided? Have some dependencies...
Hi,
I am using nrf52840, need to modify the bootloader to lookup a big bitmap table. But since the table is big, it cannot allocate within the bootloader Rom area.
Is...
Hi
i am using nrf9160 based custom board with zephyr, and trying to build GPIOTE with interrupt for a button, and led finally connect with PPI
i have been trying for...
Hi,
sorry if maybe I repeat the question. I have tested the central uart and the peripheral uart and I can make the two nordic nrf5340 devices communicate. I was also able...
Hi
I need help in understanding what the best practice is when retrieving messages from devices via nRF Cloud to my web APP.
I expect the devices to transmit messages...
I'm learning how the nRF cloud works and can't understand how the message flow is supposed to happen.
Devices send MQTT messages to nordic broker and then what?
I found...
Hi All,
I've got a project with an nrf51802, i'm trying to connect to it with a jlink edu to no prevail..
I'm running macos catalina 10.15.7 (19H15), nrf command line...
Path to sample: v1.6.1\zephyr\samples\boards\nrf\system_off
Board selected: nrf52840dk_nrf52840
-------
I am attempting to modify the sample to use a button connected...
Hello to all,
I have a problem with nrf52840 DK board, it was not detecting in nrfConnect with PC.
Previously it was working but when I had checked one sensor which is...
HI , All
I am debugging connection of "Chromecast Remote Controller" with ble_app_interactive.
I am trying to implement ble_app_interactive on nrf52832 as my application...
Good Afternoon,
I am using NRF51822-QFAA as ble remote in central mode. It connects to ESP32 and send the command for changing it's mode. I am using the RF module YJ-14001...
