Title: Intermittent non-recoverable nRF7002 error while provisioning 5 GHz Wi-Fi over BLE
Hello Nordic team,
We are using an nRF5340 together with an nRF7002 on NCS 3...
Hi I have aquestion of DEC5 pin decoupling cap.
It says later Fxx build code can be N.C.
- Does it mean it should be N.C., or it can be connected to GND or Cap. (820pF...
Hello,
We use the nPM2100 EK for getting familiar with nPM2100 for its potential use in our project where we aim to use single AAA battery for powering it.
Our usage profile...
Hi,
I am designing a custom nRF54L15 board using NCS v3.3.1 and would like to use a GigaDevice GD5F1GQ5REYIGR SPI NAND device through the nRF54L15 sQSPI/MSPI interface....
Summary
On a small fleet of identical nRF52832 units running the same firmware (NCS 2.5.1, SoftDevice Controller, BLE peripheral, LFCLK = RC with calibration), individual...
Hi,
I've been using NRF Cloud without issues (Pro subscription) and I am no longer able to login my NRF Cloud account. I tried changing password and use different type of...
Hi
I have tested direction finding examples successfully., by default parameters. Theses projects are used as "TX" and "RX" in AoA mode:
https://developer.nordicsemi...
Hello, following this question - https://devzone.nordicsemi.com/f/nordic-q-a/76417/saadc-tasks_calibrateoffset-shall-only-be-used-before-tasks_start-or-after-events_end-nrf52833...
How i'm supposed to check if the device is transmiting any data? I used nRF52833 DK as a sink and node of wirepas mesh network, added another DK and configured it as a regular...
Hi,
I'm making an firmware for the nrf52840 that communicate throw usb to a computer.
First I used the uart library that works fine but required the Jtag and Jling which...
I just cloned the latest zephyr from github and tried littlefs. However, the SPI pins have no traffic and CS line stays unchanged.
Is there something I forgot, since...
Hi, i'm working with NRF51822, and i saw on reference manual that micro enter in the SYSTEM OFF mode. The problem is i dont want the micro enter on this mode.
I make de...
Hi,
I'm working on a project using the gazelle protocol with the gazelle pairing library. Due to the fact that I use the GNU GCC compiler, I created a Makefile from the...
Dear Nordic team,
We have designed custom boards with nrf52840 chip. We observed that in one of the boards the application is not running until the swd pins of the custom...
Hi,
We are using laird BLE653u BLE module in our application. This module has nRF52833 BLE SOC. We have ST Link V2 as a programmer tool. We want to use SWD protocol for...
I have a project using NRF52840 as master in BLE central to scan BLE device.
I found all example will connect device automatically when device found
I would like to change...
Forgive me if this is already discussed somewhere - I'm fairly certain it must have been - but I can't seem to find what I'm looking for. My client's project uses a higher...
Hi,All:
As the topic,which address is the mbr jumping to bootloader by ?0x10000ff8 or 0x10001014? and how to feed the mbr para register 0x10000ffc and the 0x10001018?
Hello,
I need to use the more accurate HFXO for a very short interval to time incoming interrupts (approx 1/50 second every 15 mins)
The processor sleeps idle for the...
Dear DevZone,
I am trying to configure the SAADC on my custom nRF52840 board.
I would like to use it in blocking mode together with oversample 16x and burst enabled...
