Hi,
We are experiencing a low RSSI/range issue with our nRF54LM20 module using the nRF21540 FEM.
We have already consulted with you regarding the design under Case ID...
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
Hi
This isn't about a problem so I'm not sure if this is an inappropriate post to make here, if so please feel free to remove it, however there is no commercial incentive...
I am using the SDK v3.4.0 LTS
for modem error debugging I included: prj.conf
I am mapping errors depending on wether memory allocations failed.
I am fetching the stats...
If a Channel Sounding procedure is aborted while in flight and the ACL is then disconnected, the device settles at a flat ~1 mA with the CPU asleep in the idle thread and...
Hi,
I am developing firmware on the nRF93M1 DK and have a question regarding the Wi-Fi location feature. According to the Nordic documentation (Features of nRF93M1 — nRF...
Hello all,
I am looking to hire a developer experienced with ANT+ together with BLE and the nRF52840 SoC, possibly the nrf54L10.
I am looking for the coding for the...
,i use a nrf52840dk_nrf52840 to run once a nrf5340dk_nrf5340 board's code , I change board name from nrf5340dk_nrf5340_cpuapp to nrf52840dk_nrf52840, change xxx .overlay from...
Hello,
I use central_uart (nrf52840dk) and peripheral_uart (nrf52833dk) examples, NRF Connect SDK v1.6.0
I want to send more than 20 bytes of data,
So, I increase UART_BUF_SIZE...
Hello,
I am using the nrf52840 controller for the development ,i want to read the value from 2 channel of ADC . I just gone through the SDK example code of
SAADC, here...
Hi All,
I was trying to transmit a bare-metal minimal C program to send a raw ADV_SCAN_IND PDU using nrf52840 dev board. Code is listed below:
Here is the linker script...
I'm currently building a device that has the following functionality:
1.) wake from sleep mode and wait 5 seconds for a potential button press
2.) if the button is pressed...
Hello,
I'm trying to debug an issue where a function I wrote that should only be called under a specific condition is calling in an infinite loop whenever the program runs...
Hi, I'm using nRF52805 S112 for my BLE project. I'm using an internal RC ocillator. I would like to ask something about the clock.
1) NRF_SDH_CLOCK_LF_RC_CTIV =16 and NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hello,
I am working on using the open_bootloader with our application and running into a problem.
We are using the GP_REG to jump from our application back to the bootloader...
Hello,
I'm using the following code to loop through the flash memory sequentially and send records created by the flash_fds example:
The data stored in the records...
Hi,
How does numeric comparison works? Shouldn't both devices share parameters in order to display the same number? How can we be protected from MITM?
Thanks!
Ive added another endpoint to the OTA zigbee client example, when I run
ZB_ZCL_SET_ATTRIBUTE (ep, ZB_ZCL_CLUSTER_ID_ON_OFF, ZB_ZCL_CLUSTER_SERVER_ROLE, ZB_ZCL_ATTR_ON_OFF_ON_OFF_ID...
I'm using the nRF52 DK and attempting to use I2S to send data to a DAC. I'm using the nRF5 SDK, version 17.0.2. The last sample in the data I'm sending is always replaced...
Hi,
I have a question regarding diffie-hellman.
What exactly are we doing with diffie-hellman key? Do we use it to create another key? Or is it the key itself?
Thanks...
