Running a test that sends a small ping packet to a server about 1/minute and I'm seeing intermittent board resets. I'm still trying to track down the cause, but in one case...
Hello Nordic support,
We are designing a battery-powered device using the u-blox NORA-B206-00B module, based on the nRF54L15. u-blox support recommended contacting you regarding...
Hi Nordic DevZone,
We are currently looking at how best to handle nRF9151 programming in mass production, and I would like to understand Nordic’s intended approach a bit...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hello,
SDK : 16.0.0 Controller : NRF52840
I have 2 app_timer instance, one is used for longer sleep like 24 hours, and other is used to blink led when device is performing...
If you are broadcasting in normal mode, this code will not report an error. But if you are broadcasting in long range mode, this code will cause a FATAL ERR. If you are broadcasting...
I am wondering if it's possible to conduct a serial UART loop back test on nRF. For example, if I use a wire to connect the TX and RX pins together, and send something out...
My understanding is that Thingy:91 HW doesn’t support FOTA update of nRF52 from nRF91 since the reset control line isn’t connected from nRF91 towards nRF52. My understanding...
I am working with the udp example in nrfConnect for the nRF9160
I see that CONFIG_UDP_DATA_UPLOAD_SIZE_BYTES has the value of 10 (bytes of payload). However, I do not see...
Hi
I have my custom board with nRF9160 module running Serial Lte Modem application, and an external MCU talks to nRF9160 over UART and access using AT commands. The custom...
We are using nrf9160 and Modem firmware 1.2.3. This might be a regression of this bug .
Our concept is to switch the modem on via lte_lc_connect_async(), exchange some MQTT...
Hi,
I have a requirement, using the latest mesh sdk ' nrf5_SDK_for_Mesh_v5.0.0_src ' on nRF52 Development kit(PCA10040), I want to generate the temperature data from DK...
Hi,
this is my first time trying to use nrf connectivity tools, and my setup is a bit strage (and I have no clean DK setup to compare with:-(
I have to update firmware...
I am developing an IEEE 802.15.4 Application on the nRF52840 using the Radio Driver (v1.8.0) . I have a problem with the transmit call function. Very often in nrf_802154_transmitted_timestamp_raw...
I wrote a program for nRF51822 and compiled it with keil. The app, boot, and sdk are combined and written to the chip. However, if I write using nRF Connect Programmer, it...
Hello,
Our custom board (nrf52832, S132) seem enter to the read back protection, J-Link could not connect to the target in any ways.
We tried the command "nrfjprog --recover...
The code is running on 52832 (BLE) and transmit msg over BLE (NUS) each time GPIO is active (GPIOTE).
But same code (after adding LE CODED Phy) is crashing once it reached...