Hello,
I've been asked to create a new ticket for this. It follows on from
@ Erlend Isachsen asked:
So before marking this problem as resolved, it would be nice to be...
I am developing on the nrf9151 with SDK v3.4.0.
The device I am developing will be moving trough all of europe . My goal is to speed up the `AT+CFUN=1` conenction part of...
HI
I am currently carrying out secondary development for PAWR based on NCS 3.2.1. I understand that its communication adopts frequency hopping. I would like to ask whether...
NCS-3.4.0, on nRF5340, custom board losely based on PAN1783. No RTT backend, BLE stack works properly:
RTT enabled, BLE stack reads some garbage:
Printing is done...
Hello, our design does not use the USB block of the 52833. In the electrical schematic we have connected VBUS (AD2) to GND and we leave D-(AD4) and D+(AD6) open. Due to a...
SDK: nRF Connect SDK v3.4.0 (TF-M v2.3.0) Board: nRF9151 (seen on both nrf9151dk and a custom nRF9151 board) Config: CONFIG_TFM_PROFILE_TYPE_MINIMAL=y, MCUboot with CONFIG_USE_SEGGER_RTT...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
For our custom nrf9151 board,
The following is the prj.conf:
There are no pullups on any GPIO and for now, assume there are no peripherals connected, but there is a...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hi,
I would like to know the value of the Noise Figure for the nRF52840. How much dB is it? I am looking at the documentation of the nRF 52840 but could not find the value...
Hi Nordic team,
I'm currently working on a device onboarding flow using the nRF Connect SDK Toolchain v2.6.0 on an nRF52840 board . The onboarding process involves:
...
I am building the sample project C:\ncs\v2.5.0\nrf\samples\bluetooth\peripheral_uart, which supports MCUboot’s serial recovery of the networking core image on nRF5340DK. ...
My Power Profile Kit (PPK2) having issue after a firmware update. Now it's not even turn on the light when connected and with power switch on. I think I accidentally update...
My company does firmware consulting work. We have been asked to create a Green Power Device (Wall Light Switch) on the Nordic nRF52833 chip.
From our research It does...
I have make a PCB with a BLE5340PA module from Ezurio using the nordic 5340 soc, i want to programm the soc but it seem that there is no boot on the module.
Fortunately...
I have a preset stored in CMakePresets.json:
When I go to create a new build configuration with the preset, the extension creates an Extra CMake Arguments row with:
...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi all,
I'm working on an application using the nRF54L15 with NCS v2.9.0 and Zephyr RTOS. The device performs BLE scanning using the following parameters:
When deployed...
Hello Team,
We are working on nrf54l15 platform and using nrf connect SDK 3.0.2 We have added the support of DFU over BLE using following steps:
1. Added " CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
Can anyone clarify what information is stored in the nrf9160 chip barcode? For our manufacturing tests, we'd like to use a barcode-readable identifier on each board, and the...
Is there any documentation on what peak data rates are available on the nRF9151?
While the Cat-M, Cat-NB1 and Cat-NB2 standard max data rates are easily available, I have...
