Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
Hello, We are looking to send around 1000 Bytes on characteristic. On android app we used Nordic apis to send long write for sending 1000 byes but I am receiving only 509...
Hi team,
My customer is working on design with nRF52832, and they want to know how to defer the low drive mode and high drive mode as below?
Also, shall that be configured...
Hi ,Support Team
My customer is using our nrf5340PDK, their wrong operation caused the DK board become unrecognizable. I use the newest nRF-Command-Line-Tools_10_11_1 to...
Hello,
i am trying to activate eDRX with the unmodified at_host sample on a nRF9160DK. After connecting i get empty strings for <NW-Provided_eDRX_value> and <Paging_time_window...
Hello, sorry if this seems to be a basic or already asked question, but how could I have an example of QDEC usage with the nrf52840 (ideally the dongle) ? I would like to...
Hi,
I am using NRF52833 to develop a wireless and USB combo mouse.
My switch method is detecting VBUS to switch between USB mode or wireless mode.
But a problem is...
Dear sir ,
Get the customer's board, I can find the device at the nRF Connect for the first time, then program hex, but fail, and then I can't find the device again. I try...
Hi,
Right now, I am trying to open that example files in SES IDE. But I couldn't open.
I kept the file location like as
D:\Nordic\nRF5_SDK_17.0.2_d674dde\examples\peripheral...
I am trying to integrate cli over Nordic UART Service. i want nus control over command line interface such as PuTTY or Termite.
How to solve this and what files should be...
I have two NRF52832 boards. I cannot get the SDK to compile so I'm going at it barebones style.
Transmitter Board code:
Receiver Board code:
The receiver board never...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
I use nrfjprog in a CI system (on Windows 10) which has multiple NRF52 boards attached to it. The boards are all run in parallel with the -s parameter to nrfjprog and the...
Hello, i have an issue with softdevice API combined with timeslot API. I use timeslot API to scan for packets one time (one time interval) with 30000us. Then before timeslot...
Hi, I'm using mqtt_simple example based application to send BLE tracking data through LTE on custom boards. UART is used for connection between MCUs. Power is ON constantly...
