I am trying to get a SST25 spi flash running, but the jedec,spi-nor driver does only partially work.
As i understand now the jedec,spi-nor driver only works with CFI compatible...
Hi
I have a question regarding the power consumption of my own PCB.
I have taken a power profile of the nRF9160DK dev board and of my own PCB with the same software, but...
hardware:nrf5340dk
The above 45 pairs of IQ data are a set of data that I have received.The maximum amplitude of the IQ data I received seems to be only 128, which means...
I originally had a case using the 52832 QFN48 package, but then the customer needed to use the 52811 functionality. We found that the PIN definitions of 52811 and 52832 on...
Good day!
I want to test two sensors, MPU6050 and MAX30101, in a Xiao nRF52840; however, I am struggling to obtain data from the MPU6050 sensor. I noticed that even if...
Hi Nordic support team,
I'm new to Nordic chip and using nRF5340 Audio DK for my project,
and I'm trying to build zephyr/samples/blutooth/iso_broadcast_benchmark , which...
Hi,
I have a piezo microphone with analog output and would like to record from it using the Line In AUX on nRF5340 Audio DK.
Currently, I am using the break out pins...
Hi,
I want to connect X-NUCLEO-NFC08A1 with ST25R3916B to nRF5340 board by adding a SPI node to device-tree source. After compiling and flashing the board, triggering interrupt...
I have been trying to implement the wifi scan or wifi provisioning code on a module (MS12SF1) which is a combine wifi + ble module
The setup looks like the image shown below...
Hello,
I'm a relative neophyte when it comes to non-hardware aspects of WiFi ICs, so I have some basic questions about the nRF7002; these are features my client is asking...
I wrote a code for GPIO interrupt when DRDY pin goes high to low(Data ready) interrupt should occur and call a function but it is not working Below is a code:
intDRDY =...
Hello,
I have a use case where I need to use UART_RTS and UART_CTS as GPIO for toggling the led. I also want to use the other two pins UART_TX and UART_RX for handling UART...
Hi,
My customer tried using the keyboard we made based on nRF Desktop with NCS version 2.1.0 with an iPad and noticed that most of the keys work, but space bar does not...
hi,
I want to know how Bluetooth allocates channel resources as a master.
Assuming a Bluetooth master is connected to 8 slaves simultaneously, how does the master allocate...
I don't want to use nrfjprog as the runner. I want to use jlink runner when flashing. However it doesn't work, neither do nrfutil.
nRF Connect for VSCode doesn't work when...
Hi, I am working with ncs 2.6.0 trying to implement some logs using the DiagnosticLogs cluster
But It looks to me like it is not impemented/supported yet.
For testing...
Dear Sir,
I just want to capture DTM packets using NORDIC sniffer. The Wireshark is the newest version. My chip is 52840 with nordic snffer bin file. Thanks.
with regards...
Hi guys,
We are building an IoT device on nRF9160
The main protocol is MQTT and we are using AWS IoT Core as a Cloud provider.
MQTT client is based on nRF Connect SDK...
Hi
I am powering the nRF52840 from a 3.3V DC power supply and connecting it with a IMU thats cannot go higher than 1.9V on the I2C bus
I use 1.8V.
Will the I2C coomuncation...
Hi,
I use our customer board that enable the i2s to the DAC to speaker. However, i only verify the play a wav file directly that seems work normally but our target is playing...
The product page for the Thingy53 only shows hardware files for the v0.8.0 board revision, not the 1.0.0 or v1.1.0 board revisions.
https://www.nordicsemi.com/Products/Development...
I was programming wifi scan example with nrf7002dk_nrf5340_cpuapp configuration. The mac address was not setting by default so I did it manually by using the function provided...