Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hello,
i have built my own custom service.
I have 13 characteristics ....
But in NRF Connect on an iphone, i can see 13 characteristics , but only in the first there...
Hi
Technically this is a Zephyr question, but googling the issue gave no success. Also, reading the Zephyr docs gavve me no clue.
I have a custom nrf9160 board with an...
I'm trying to capture events like accessing an invalid idx of a C++ vector
I'm using the method at , like this:
std::vector<int> my_array;
my_array.at(10000);
...
Hi,
I want to use the SAADC to measure the voltage on the VDDH pin. I am using a design based on circuit config #4 and following the SAADC example in the SDK version 15...
Hi,
I am using nRF mesh Android app version 2.1.4
I have flashed the devices with light-switch example application under nRF5 SDK for mesh V 4.0.0 on PCA10040 DK. I'm...
Hi,
I have a custom application running on a custom PCBA using the nRF52840 MCU. The Softdevice (S140, v7.0.1) is also utilised because the main application supports BLE...
Hi,
I am looking for the timing of when a connection event will happened. Radio Notification seems the right method for me since it provide an interrupt right before an...
I'm looking at the feasibility of using extended and/or periodic advertisements from an NRF52 to be received by a cell phone. I've used nRF Connect on a couple slightly older...
We have a multi protocol project THREAD and BLE. It currently uses the BLE DFU for OTA updates. We would like to add the THREAD DFU so we can use either transport mechanism...
Hi -
I have 2 questions:
1) I am looking for an example application that demonstrates acquiring acceleration data at high ODR of 5kHz from LIS3DH sensor using nRF52832...
Hi
I had got some problem with fds_record_write(). I found that I couldn't get the correct data from flash without waiting fds_evt_handler( ) that was called after calling...
Hi, I would like to test interconnection between an android phone with nRF Connect (central) and nRF52840 DK (peripherial) in long range mode. My question are:
Does it...
Hi,
I have a problem when i try a dfu on my device for the first time.
To explain, my device is flashed the first time with NRFJPROG, and i flash the SD+BOOT+APP.
So...
