Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hello,
I just received my Thingy:91X which I purchased through DigiKey. I am trying to connect it to hello.nrfcloud but I keep getting the following message: " The fingerprint...
With reference to the Thingy:91x reference design, I see that the LNA (SKY65943-11) on the GPS signal path is powered by one of the switching converters from the nPM1300:...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Hi Guys!
I have nRF52840 Dongle (PCA10059) 1.2.0. I downloaded Nordic exmaples repository. I try to however start and load any HEX file with program from Nordic repository...
some questions for power consumption of 52840.
We've planned to use about 10 to 30 nRF52840 devices for advertising TX mode. One scan mode device which is connected with...
I have a device based on the Nordic nRF52832. I am using softdevice s132. I am using Nordic nRF5_SDK_15.3.0_59ac345. My Android device I am testing with is running Android...
I recently bought a reel of nRF52840 and received rev C0 (Which is Engineering C). We require long range in our solution (Coded PHY). I was reading the compatibility matrix...
Hello,
I'm trying to stream data at ~ 30KB/s rate. I use nRF52840 development board with S140 as peripherial and smartphone with "nRF Connect" app as central. UART example...
Hello, Nordic.
A while ago, debug terminal do not appear in Segger Embedded Studio, and nothing happens when I click View -> debug terminal in the tab bar.
Currently...
As far as I understand, the nRF52840 USB dongle can be flashed via USB if there's a DFU capable bootloader installed (and it booted *into* that mode).
Once I got the dongle...
Hi
Good day!
I am new to this BLE module. I have worked out an application using nrf52 DK (nrf52832 SoC ) and now I want to use Ebyte module E73-2G4M04S1B which is based...
Hi team,
I am using nRF5_SDK_15.3.0_59ac345 and nrf52832 controller. I am using nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_uart example code and the hardware...
Hello,
Please check my schematics with PA / LNA.
I have problems activating PA / LNA, the connection is very difficult when using the battery, I am forced to use external...
Hello,
Every time I try to run any example I download online for my nrf52832 board I get dependencies errors after locating the project folder to the sub "examples" folder...
I am trying to get battery % from the thingy91. I have the AT command AT%XVBAT running successfully. It returns what I assume is millivolts. However these value are higher...