We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I tried to switch to OAT. Now I use new API
" api.nrfcloud.com/.../ long-range/devices/bulk" with OAT bearer token for devices creation
instead of old API: " ">api.nrfcloud...
Hi Team,
Please help to assist below customer concern regarding MPN :NRF54L15-CAAA-R7
They are looking for China typically require a valid Radio Transmission Equipment...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
Hello
I am preparing for Bluetooth SIG certification. I use nRF52810 / SDK15.0.0 / S112 6.0.0.
I've been helped by Nordic about QDID before.
https://devzone.nordicsemi...
Hi there
After initializing the SoftDevice S132 V6.1.0, I request the HF crystal by calling the function sd_clock_hfclk_request():
Later in the code, after a BLE connection...
SDK:V16.0.0
chip:52832
development kit:window+keil
I trying to combine libuarte and ble_central\ble_app_multilink_central\. My project work well in ble_central. But...
Hello everyone, I need to build a photo capture application.
And the CMOS sensor go through MIPI-CSI2 interface.
Is there any example code and library for nRF5340?
Hi,
How should the USB pins be handled in case I don´t want to use them? Should they be just left unconnected?
What about VBUS pin?
Thanks and regards,
Juan
Hello,
I got the issue to run the NRF9160 DK as an external AT-Modem. What I need to do is to issue AT-Commands over the UART, which control the NRF9160 modem through an...
Hi , I am running zigbee cli example code from sdk and configuring nrf52840 board as coordinator and trying to add xbee module to zigbee network. Coordinator is not accepting...
OK, a bit of confusion somebody can clear up for me, I hope;
Does NRF_SERIAL_EVENT_RX_DATA get sent when there is ANY data in the RX buffer, or only when the RX buffer is...
Hello
I am developing peripheral interfaces on nrf9160 dk, For I2C, sPI and ADC I am not able find exapmle codes. ALso could not find api required for the same to develop...
Dear nordic:
I am working on a tool which can collect data from multiple ant+ sensors with different device types,like a bike computer.
It allows user to assign up to...
I want to communicate with two nRF52 devices without pairing?
It is possible? Yes means kindly give the realtive examples.
Maximum data length...
Thanks.
Hello there, I need to ask if these two; NRF M 24L01+1712AB , NRF M 24L01+1609AH (one with external Antenna) are still supported and have official libraries , and if not supported...
I'm trying to advertise on the coded phy, but SDK 16 seems to have a block in place against doing this when you use S340. I can obviously edit this, but I don't normally edit...
After Installing JLink 6.62 it offered a firmware update for the connected JLink. I performed the update (Firmware: J-Link OB-SAM3U128-V2-NordicSemi compiled Jan 21 2020 17...
