Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Draft — ready to post on Nordic DevZone / Zephyr mailing-list
Title nRF5340 DK + MCP2515/TJA1050 module — can_start() always returns -EIO even in loop-back
Hardware...
Hi We are working on setting up CI/CD pipelines for our nRF application. The application is set up as a stand-alone application with its own west workspace. It uses external...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello.
I used to download (& install) nRF Command Line tools from terminal with this command (in Dockerfile, but it doesn't matter)
Since you've changed the...
I found half of the information I was looking for (minimum voltages) from: https://devzone.nordicsemi.com/f/nordic-q-a/47546/nrf9160-enable-pin-voltage-specification W hat...
Env: SES, nrf52 DK, Linux
Hi
I need to define a buffer (array of structure) in order to buffer readings. If i have more RAM I should create a bigger buffer if I have...
We're using the nRF52832 as a peripheral and server. A central and client (tablet) connects to the nRF52832.
Yesterday I noticed that sometimes the tablet will try to perform...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
What for this macro HWFC...
Hi, I'm looking for a PCB antenna design for nRF52832 based on 0.8 mm thickness four or two layers stack up .
I found some examples but based on pbc of different thickness...
Good morning,
I'm designing a new product based on the nRF52840 device (s140) and power consumption is one of the key parameters for my project.
The equipment (peripheral...
I'm debugging some corner-cases with my own DFU process and Bootloader. I believe I hit a race condition in which sd_mbr_command() was called before the source of the new...
I am trying to make a service discovery on a peripheral device using a nrf52-DK (pca10040). I built my project around the multi-discovery example from SDK 15.3.
When performing...
Hey all,
I'm trying to replace the nrf_cli_uart transport layer with the CDC ACM equivalent (nrf_cli_cdc_acm), since I have an nrf52840 dongle and can't use the uart libraries...
OS : Ubuntu
SDK: 15.3.0_59ac345
Base example : peripheral/saadc
HW : nRF52832 DK PCA10040 1.2.1 2017.49 682663245
Hello, i would like to make sure the ADC acquisition...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to check for debounce of a level on...
