Hey there!
I am facing a very frustrating issue, where my nRF54L15 (custom board) BLE peripheral just won't appear in mobile apps.
For example, right now I am trying to...
Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
I want to read timestamp in my nRF9160 device and found that "z_tsc_read()" function in Zephyr RTOS will do that. However, I am not able to include the main library of the...
Hi,
We are developing mesh control lighting system with nrf52832, now we're able to control devices through mesh.
But now we're having problem with showing node state...
Hello,
I have two devices, one central and one peripheral and I try to implement whitelist. I took a look at ble_app_hrs_c example and the whiltelist is working on central...
Hello,
I am using ble_app_blinky. I have a basic query about event handles. There are lot of event handlers registers as part of initialization. Will all these event handlers...
Hi all, we has experienced two PPK boards start to give faulty reading after several uses. I attached two screenshots about current reading with same setting on the DEV board...
Hi,
after having a little break from ot and working on another project, I am back working on getting the NRF into systemOFF. to get back into it I just made a very small...
Hello there,
Prior to updating to the latest modem firmware i was able to successfully get responses from the DK.
Running the Asset tracker app as well as AT Client. ...
Hi
I am currently trying to connect the sht31 temperature / humidity sensor. First, I made an implementation based on the twi_sensor example. I did it all, the temperature...
Dear all,
I am quite new to embedded programming and I am looking for a tutorial/example code in order to communicate/configure an accelerometer sensor (LIS2DH12) with NRF52...
Hi,
I am running SDK 15.3, nRF52840 on a custom board, Softdevice 6.1.1 and SES.
When running the secure dfu example I find that the two segments uicr_mbr_params_page...
Hi,
NRF52932, s132.
I am currently migring from SDK 14.0.0 to SDK 15.3.0, I just finished to migrate from SDK 13.2.0 to SDK 14.0.0. The project with my app compile but...
Hi
I want to transfer a text filebetween nrf51 to nrf52 .Is this possible in nrf device. If it is How can i proceed ?. I am using NRF 15.0 SDK.
Please help me on this...
Hi
We are using today nRF52832 and communicate through Nordic UART service (NUS).
Sometimes we would like to transfer files from our device to the app. This is going very...
Hi All,
I have an application running on the nRF52832. From within the application I can store data to 0x2000 2010 - 0x2000 2028 and read the data back after a reboot/power...
Hi,
I need to generate a PWM signal with exact 2.048 MHz. I've just realized that
allows only decimal frequency. Even if I take 16 MHz and toggle it every 7,8,9 still...
