Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
I have an nRF52840 based peripheral running SDK 15.3.
I have a custom service with a write characteristic and a read characteristic. The peripheral supports multiple connections...
As far as I can tell the values are inverted.
4.8.2.2.1.1 Occupancy Attribute
The Occupancy attribute is a bitmap.
Bit 0 specifies the sensed occupancy as follow:...
Hello
I am using nRF52 DK, I am trying to use PIN 30 as Pulse train. The following while loop is expected to send out Pulse train of 2microseconds period but instead, it...
As far I know BLE mesh uses the 3 advertisement channels for communication without any synchronization mechanisms. When the mesh protocol emits a package it will send the...
Hi
Why is Mac OS no longer listed as a supported operating system for the nRF Connect SDK (see http://developer.nordicsemi.com/nRF_Connect_SDK/doc/0.3.0/nrf/gs_ins_os.html...
Hello,
I have a question regarding BLE characteristics and bi-directional communication. Assume a service like Nordic UART Service (NUS) is used, then there are two characteristics...
Hi,
we tried the example from the NRF SDK (15.3) with the USBD_MSC. The logging looks good so far and we have a data micro USB connected to the nRF USB Plug of the dev board...
Hello All,
I have 2 evaluation boards nrf52840 EVB "PCA10056".
I would like to run on them the "ble_app_uart" in "nRF5_SDK_15.3.0_59ac345" as following:
A custom board...
I used nrf52832 to port the program from SDK14.2 to SDK15.2 and there was a problem. In SDK 15.2, the program functions normally in the online debugging state, but the function...
I like to use 2 server boards and 1 client board in mesh as custom model. Is it possible to use client to communicate with 2 or many server's without using instance in client...
Hello,
I am trying to conenct the DK to the nRF cloud. I registered the SIM successfully and then proceeded to insert the sim and power up the unit. The LED 3/4 sequence...
Hi there! I am looking to implement a Zigbee powered device using the nRF52840. I have very good hardware knowledge of said chip, but not so much of the software part (especially...
In the documentation for app_uart_init() - there is a statement indicating:
Function for initializing the UART module. Use this initialization when several instances...
device addr：38 D2 69 BB B9 E7
The address type returned by the nrf_ble_scan_address_type_decode function is BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_NON_RESOLVABLE。
The type...
