Hi,
I am working on a custom nRF52840 design (using nRF Connect SDK v2.9.3) and I have accidentally locked the chip via APPROTECT.
My major issue is that on this hardware...
Hi, I am unable to read GPIOs (always getting 0x00000000 from gpio_port_get or 0 from gpio_pin_get). My main project is https://github.com/marcuswu/leaf-fall/tree/main/firmware...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hello,
Overview:
Currently we are using nRF9160 we are using mbedtls library for generating EC key based certificates (self-signed and CSR). Our code is built with TFM...
Hi Team,
I just wanted to ask is amazon sidewalk support package for nRF54lm20b is available. If yes, please guide me with steps to add it to the project.
Thanks and...
Hello, I wanted to update my project (Custom board using the nRF54L15 ) to the v3.3.0 SDK since this fixed a BLE bug with the v3.0.1. version. To my knowledge I did not change...
I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
Hi,
I am using nRF52832's ADC function to do my project, and I have an analog signal level problem.
I am try to connect MPX5100 sensor to nRF52832's ADC port, but the...
I am trying to use ARM GCC in macOSX and successfully generated .HEX file with the most simple project: the blinky project without softdevice. After setting up the project...
I am trying to use dsm_local_unicast_addresses_get() to store the address of each node, however it seems that when the board is restarted the value is lost, and node_address...
Hi,
I have troubles using nRF Mesh with my Vendor model.
I have made a Vendor Model that should allow me to send messages through Mesh. Once my boards are provisionned...
Hey everyone
This is sumanth, I am working low power node in mesh networking, I followed the procedure mentioned in below link for building and flashing
https://www.nordicsemi...
Hi I have a device which can get RSSI value from other devices.
But how do we get RSSI of my device itself.
i.e How to print RSSI of local device on the same device terminal...
Hello everyone,
Today I worked on custom bootloader and according to the article infocenter.nordicsemi.com/index.jsp I tried to load output hex file from IAR on board via...
I want to add a new ble service in hrs example(sdk15.3),I build and run the hrs example.and then I open the terminal emulator, but I can't find anything.I try to click the...
I want to use nRF52840 BLE with STM32F745ZG microcontroller and using atollic studio for coding. is it possible to use nRF52840 with the microcontroller? if it is possible...
I'm using SDK 15.1, nRF52 in custom units, toolchain GDB, addr2line
A little background -
We use System off mode and then use a button press to come out of it.
Before...
After doing a detailed review for the datasheet for nF51822, I can find no input leakage current specification for the digital inputs or ADC inputs. Where do I find this specification...
Hello,
for current consumption measurement of our PCBs, I created a special software. This software does boot up, puts SPI FLASH in power down and go to sleep forever. All...
Hi, Sir:
I am using nRF9160 for development, I would like to complete a COAP client,so I need to refer to ......./nrf/samples/nrf9160/coap_client. I installed NRF_Connect_SDK...
