Our prototype is back. At first, I used NRF Connect to flash it, but the official PC software couldn't flash the firmware. I followed the wiring instructions: (1) connect...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
I find the smallest connection interval I can set on 52840 (and 832 as peer) is 8 units (10ms), and I am not sure if that is reasonable.
My configuration:
52832...
I have a question concerning this tutorial : devzone.nordicsemi.com/.../ble-characteristics-a-beginners-tutorial
i have same problem than Milton (comment under the tutorial...
We have procured nRF52-DK development board from Mouser India and we are using S140 stack on the Windows platform for our PoC.
Our application requires that nRF52840 should...
Hello,
I would like to modify the current default SRAM partition from 64k (secure), 64k (bsd), 128k (non-secure). I would like to change it as follows; 8 k (secure), 8k...
See: https://devzone.nordicsemi.com/f/nordic-q-a/46833/nrf-connect-can-t-see-nrf52-dk/185284#185284
I have been developing a peripheral with nRF52832 and SDK 15.3.0.
I...
I'm stuck over fds_init() which hangs on mbed-os using SDK 14.2
I am calling fds_init within bleInitComplete callback as follows:
BLE & ble = BLE::Instance ();
ble...
Hello,
The pwm example shows changing the duty cycle inside the main while loop with delay wait.
I would like to get rid of this delay wait by putting the app_pwm_channel_duty_set...
Hi, may I know whether there is a way for nRF52832 chip to directly have access to the variable gain amplifier (VGA) inside the chip? Namely, our input signals goes directly...
Hi,
I am using the sdk 14, S132, ble_app_uart example.
My nordic chip receives data from the MCU over UART and passes out to mobile application over BLE.
using the nrf...
hi i am trying to integrate nrf_butoonless_dfu service in ble_app_uart code in nRF sdk 15.3.0,
i have added the all the required source files and include files and macro...
I am attempting to implement an application using the s140 6.1.0 softdevice on an nRF52840 which "concurrently" advertises as a connectable device while at the same time transmits...
I try to solder a EBYTE NRF52840 module by my PCB and connect with SEGGER programmer. I try to connect to 4 wire VDD, GND, SWDIO, SWCLK, like the one that I have with NRF52832...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0. I use gcc. I just got it to link and flash and I'm seeing RTT logging OK, to a point. I also have the flashlog in use...
in my application use nrf52 connect with max6675 thermo couple for read temperature
max6675 is configurable in spi mode.
in main.c
in 'nrf_drv_spi_init' not...