Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi, I have a question regarding the behaviour of a button in the nRF App in Android, sometimes the button "READ STATE" in the "Generic On Off Server" configuration changes...
Hi,
I have managed to run DFU mesh example and successfully updated firmware of whole mesh network. Now i am looking for options to perform customized DFU over mesh . Lets...
We are experiencing issues with nrfutil being flagged as containing malware, see screenshot below. Has Nordic experienced this before, is there something we can do to stop...
Hi
I have reported this before and now that you are a quarter away from a fully featured mesh sdk can I ask you to please enhance the SDK so that you supply a function that...
I'm evaluating possibilities of BLE-LESC Pairing/Bonding with the ble_app_hrs peripheral on the nRF52840-DK with SDK 12.3 and SoftDevice s132. To see what's going on in the...
Is it possible to flash multiple custom boards using sagger DKs at the same time?, assume 2 custom boards and 2 DKs, would they be able to flash the custom boards in parallel...
There are many places in the file fsm.c that have this compile condition check
#if defined FSM_DEBUG
blabla
#endif
that is wrong. The compiler will ignore it. There...
Dear Nordic,
Hello, I have to configure 2 UART. I have saw this post .
however, I have made a demo version for the project without 2 UART function, so I hope to apply...
Hello, I´m trying to compile the BLE Heart Rate service projects using SEGGER Embedded Studio. After importing the project from nrf52 SDK, I tried building the project but...
Hello,
I want to implement home automation project using 3 nRF52840 dongles. i.e I want to connect all the 3 dongles with each other and the signal sent from one device...
Hello, I am trying to design a product based on BLE MESH. I would need gateway to be able to accumulate data from network and send it outside. I need that gateway to connect...
Hi,
I have gone through the "ble_app_hids_mouse" example program. So far the program seems to work great, but how do we take control of the buttons since the function used...
Hello,
We have plan to use nRF52832-CIAA with external antenna connector (MHF4). I noticed that in 4-layer reference design layout there is quite big square keepouts on...
Hi,
I am using sdk 14.2.0.
i am using freeRTOS,created 3 threads.
all are running fine,but just for while(2 - 3 minutes).
after that, all the threads stoped.
may...
Hi,
I am doing OOB commissioning with OpenThread. According to section 10.12 of Thread 1.1.1 specification, Active / Pending Operational Datasets need to be persisted to...
