We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
I have two nRF9151 DKs and want to evaluate direct, SIM-free DECT NR+ communication using FT and PT roles. Please help me with:
- DECT NR+ MAC/PHY modem firmware, rather...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi, I was confused about the behavior of GPIOTE Handler module。I defined a handler(gpiote_event_handler) and I hope when the GPIO Pin(0.14) is changed from high to low or...
I use the example usbd_ble_uart with SDK_15.3.0. I need to send any byte received from the terminal via BLE. Do not wait until the buffer is full or the end of line character...
Hi,
I am trying to combine the usbd (hid mouse) example with the uart central example to run on the nRF52840 dongle. I am having a lot of problems and am not really sure...
I have some colleagues that are working on a project where they want to use the nRF52 as a general purpose IO processor alongside providing an BLE interface to a host Linux...
I installed SDK 15.3.0 build 59ac345 and started working though the DFU secure boot loader example. In the 15.3.0 documentation it says
Setup
You can find the source code...
Hello
We are using custom board which has two chip configuration for BLE stack. Main MCU runs the Zephyr Host only BT stack in peripheral mode.This is supposed to be GATT...
I am trying to compile the SPI example in SDK 15.2.0 for nrf52810. I am getting a compiler error in SES on nrfx_uart.c:
I modified the project according to the SDK documentation...
Dear all,
Is this possible to flip a switch on the board to get nRF9160 IOs at 3.3v rather than 1.8v ? I have a LoRa module that requires TTL 3.3v UART signals, and it...
Hello,
I believe I have found a possible race condition in experimental_task_manager / task_manager.c, task_events_wait().
The race occurs if a task calls task_events_wait...
Hello, I'm working with an example of ble_app_uart with SofDev132. I have modified the code a bit but I still use the nrf_pwr_mgmt_run function. The power consumption is 2...
hello, i am complete beginner to this field of MCU, i never worked on nordic MCUs. i am able to program the dk-board using the usb cable and readymade hex file provided in...
Hi,
I'd like to enable paring/bonding for a minute only when a button is pressed. So I need to disable pairing. I've learned that it should be done with
in "ble_evt_handler...
Hi,
I would like to have two different twi managers. One with TWI0 and one with TWI1. But if I try to enable them I get an error:
sdk_config.h:1810:22: error: unable to...
Hello,
I am new to BLE and trying to understand basic concepts.
Connection interval ranges from 7.5ms to 4sec. Device is doing Frequency hopping on all channels from...
