Hello friends from all over, I am a beginner. Recently, I have been working on synchronizing lighting animation effects between devices driven by a mesh network and have encountered...
Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hi,
We are designing a battery-powered product based on two Nordic chips and would like your recommendation on the overall architecture before we freeze the hardware, having...
Hi,
GSMA SGP.32 v1.3 section 3.8.2 and 3.8.4: the device selects IPAd or IPAe mode with the TERMINAL CAPABILITY command at UICC initialisation. Tag 84 , byte 1, bit 1 set...
Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
Problem:
After every wake-up our device reports a SoC 10–28 % higher than it reported just before going to sleep.
Between sessions the nRF5340 is in System OFF via sys_poweroff...
Hi Nordic team,
While benchmarking quantized INT4 (`s4`) matrix-vector multiplication (`arm_fully_connected_s4` / `arm_nn_vec_mat_mult_t_s4`) on an **nRF54LM20 DK (`nrf54lm20dk...
I want to put the BLE program to the firmware of another STM chip and load the program via the I2C to the nrf52832. Will it work? If yes, is there any tutorial or example...
Hello,
I'm using nRF5 SDK with version 15 and nRF52832 IC. I want to sample some data with 3200Hz sampling rate. I can set the timer minimum 1ms Which means 1000Hz. How...
I want to write at the end of memory ROM data in address 0x7FFFF
uint8_t tst_arr[1] = {6};
sd_flash_write((uint32_t*)0x7FFFF, (uint32_t*) &tst_arr, 1);
Is it correct...
Hello ,
System configuration
Set up 1 Adafruit BLE Feather running stock central UART example from NORDIC SDK version 15.0`examples connected to host PC using USB
Set...
The dedicated NFC pins on the nRF52840 are P0.09 and P0.10. However, these are noted as "Standard drive, low frequency I/O only " pins, with "l ow frequency I/O" defined as...
Hi, I'm facing an issue after provisioning the Client and Servers from Light Switch example of Mesh SDK 2.0.1, using the Android App. Provisioning is successful, however,...
Hello,
Following on from this question , I've been trying to identify the source of unexpectedly high power consumption when using the RTC. In order to test this, I am using...
Hey all, I am using an NRF52 DK and am trying to combine the 'pwm' and 'ant broadcast' examples. Both examples compile fine on their own, but when I try to combine I am getting...
I have a number of (probably naive) questions regarding the internal temperature module on the nrf52832.
1) Regarding the FICR values for temperature. Are these programmed...
Hi,
I want to run the default DFU, and run an application on top of that. In order to configure the bootloader, this is the folder i am currently using the dfu bootloader...
Hi Team,
I am a bit confused in terminology used in BLE MESH PROFILE specs.
Can someone help me to understand the difference between subnet and group ?
Are both the...
Hi, I've been developing android beacon application that connects with your chipset NR5283.
What i am trying is make connection to Ble Mode from Peripheral mode, and stream...
Hi all,
I've gotten the saadc example working on my product, reading in values as I would expect. However, I have two problems. First, I want to be able to use multiple...
Hi,
The NRF toolbox iOS app contains a DFU feature which allows users to update there firmware for the nRF52832 microprocessor.
1. Rather than storing the firmware updates...
It looks like the last discussion of Sniffer on Devzone was 2-3 yrs ago.
I’ve ordered the nRF Dongle and will download the Windows-based nRF Sniffer app.
i can run this...
