Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hi,
We are designing a battery-powered product based on two Nordic chips and would like your recommendation on the overall architecture before we freeze the hardware, having...
Hi,
GSMA SGP.32 v1.3 section 3.8.2 and 3.8.4: the device selects IPAd or IPAe mode with the TERMINAL CAPABILITY command at UICC initialisation. Tag 84 , byte 1, bit 1 set...
Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
Problem:
After every wake-up our device reports a SoC 10–28 % higher than it reported just before going to sleep.
Between sessions the nRF5340 is in System OFF via sys_poweroff...
Hi Nordic team,
While benchmarking quantized INT4 (`s4`) matrix-vector multiplication (`arm_fully_connected_s4` / `arm_nn_vec_mat_mult_t_s4`) on an **nRF54LM20 DK (`nrf54lm20dk...
I'm aware of https://devzone.nordicsemi.com/f/nordic-q-a/125252/reset-over-ctrl-ap/555253?focus=true
Is it possible for an nRF54 to safely use the CPU access to the AP registers...
Hello, I'm having trouble to make the image transfer demo work.
I flashed the .hex files found here: https://github.com/NordicPlayground/nrf52-ble-image-transfer-demo to...
Hi all,
I am adding PWM to light switch server . I added success. PWM function run OK. I use PWM1,PWM2 with Timer 1 and Timer 3 and PWM library example .If I call function...
Dear Support Team,
I’m using nrf52832 and SDK 14.2.0. In my project ,there are two dsp,one is nrf52832 and the other is ntk658, they connect via uart with each other. ntk658...
Hi,
I am developing nRF52832 peripheral, SDK15.
Let me know about whitelisting.
I'd like to below functions.
1. Delete item(device) in white list.
2. Changeing...
Configuration is all 12 combinations of the following 3 x channels, 2 x modulations, and 2 x bit rates were tested to find the worst case. More substantial testing was to...
when i upload the hex file of a s132 softdevice example program through nRFgo studio,
its shows hex file uploading failed and shows this message "Invalid SoftDevice, data...
Hello Everyone,
I am facing an issue when trying to connect back BLE central again after disconnecting it from the BLE peripheral once.
The issue is reproducible as follows...
If I want to send two byte, how can I do? I use the https://github.com/NordicSemiconductor/Android-nRF-Blinky sample code.
In BlinkyManage.jave
public void send(final...
hi All!
I'm trying to use new SD140-6 function sd_ble_gap_adv_set_configure() , according to spec. if last PARAM is NULL, function behavior : " When this function is used...
Hello, there was a strange problem in the mass production of my product. The previous batch of problems was less, about 0.5%. The later batch is quite serious, 45 of 500 products...
Hej,
on trying to update firmware on nrf52832 over the air I'm getting the error message INSUFFICIENT_RESOURCES.
Actually I don't understand the error message because...
I want to put the BLE program to the firmware of another STM chip and load the program via the I2C to the nrf52832. Will it work? If yes, is there any tutorial or example...
