Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hello,
I work on an application which use the pc-ble-driver 1.0 as BLE central for handling external peripheral devices.
Now, I am working on bonding procedure. To make...
I'm attempting to take a 115k baud stream of NMEA sentences from a GPS sensor, and outputting it to a phone based on the UART example. While I'm not sure if BLE is perfectly...
Using the ble_app_uart example on the nRF52 PDK, I can easily send multiple packets per connection interval--if I send a long string using ble_nus_string_send(), the notification...
Hi.
I've just received my nRF52840-PDK and now I am trying to run usb examples from SDK 13.1.0.
I have started with VisualGDB using arm-eabi toolchain and USB HID Generic...
Setting interrupt priority according to FreeRTOS documentation is an inverted priority sequencing, i.e. lower number is high priority. However in the freeRTOS example provided...
Hi,
I am seeing an issue where after enabling read back protection (rbp) on NRF52 and using sdk 12.1 the tag goes to state where it drains a lot of current.
command used...
Hello!
I'm using SDK 12.3.0 with nRF51822. Unfortunately since the begining I've got a problem with TWI interface. It keeps crushing my app. For no reason. At the beginning...
Hello,
I am using sdk 12.3.0 and pca10040 board. I want to update the firmware OTA. I am following this post
devzone.nordicsemi.com/.../
I am stuck at step 4)...
I am using the nRF52832 development board, S132 and SDK11.0, I have some questions about Bluetooth pairing,The project under the link:examples\ble_peripheral\ble_app_uart...
when we use twi to transmit data in iic mode ,the nrf52832's power is unacceptable,too high!we read and write data in 50times per second.every time, we transmit 24 byte data...
I JUST NEED TO KNOW NUMBER OF ON PULSES PRESENT IN THE PWM OUTPUT CAN I USE PIN CHANGE INTERRUPT TO COUNT THE NUMBER OF ON PULSES OR SOME OTHER METHOD IS AVAILABLE
Hi,
We need to pass the radio certification and in order to simplify the setup we created an application to setup BLE TX/RX/CC/MC from an NFC command but we meet a strange...
Hello,
As a lot of person, I have a problem for use nrf52832(pca10040 board) with spi as slave.
I check my master with salae probe tool and this part is correct. Chip...
Hello,
my nRF52 Preview dev.kit don't upload the last 2016 march 15 firmware update
from nRFgo app. It gives me always an error and the progress bar stay at 0% value.
...