Hi,
I am currently testing the dect_shell example on two nRF9151 DKs and achieved a range of ~500m. I want to transition this setup into a multi-hop mesh network topology...
Hi: The device shows successful reconnection, but the mobile end is not connected.
And the connection information displayed on the device is (public), which is actually...
I am trying to measure the 300mA system current.
I cut off the system lane and connected Vin, Vout.
And when in ampere mode, the system is not turning ON.
(When I replaced...
Hi Nordic,
I have a custom board using a Raytac MDBT53 module with nRF5340. The board is designed for 3.3 V / LDO mode, but during bring-up I likely flashed firmware/configuration...
Hello Nordic support,
I am using two nRF54L15 devices with NCS v3.0.1 and ESB DPL at 1 Mbps. Auto ACK is enabled, the payload is 252 bytes, and the retransmit count is 9...
# SoftDevice Controller assert during DTM receiver test at dead/marginal RF link (nRF52833) ## Summary On an nRF52833, running the nRF Connect SDK Direct Test Mode (DTM) 2...
A customer implemented a nRF52840 (QIAA package) and says the output power is about 10dB lower than expected. Having done multiple nRF52 designs with good results, I reviewed...
We create library for work with software serial, we use two modules gpiote, timer.
We have done software serial one instance but we need four (actually just for rx). We don...
HI,
I am using nRF51822 S130, SDK12.3.0
I created private key for application code and public key for bootloader. Just few days ago, the zip file can upload to the device...
Hi,
I use NRF51822 + S130 + SDK12 platform, my device work in CENTRAL mode, I want send data to peripheral every 10ms, code like this:
while (1)
{
while (m_free_tx_packet_count...
Hello,
I am currently working on nRF52840PDK baesd project, where I want to use BLE using RIOT OS. So, please can you provide any example for RIOT OS based BLE or any details...
Hello all ,
I am using nRf52832 and i found PWM conflicts with Softdevice: We were able to create a sample PWM application which works fine independently. When we merge...
I'm developing a system which consists of 1 or more remotes (3 or 4 max) that have to communicate with a single host.
I need a fairly simple protocol, low power optimised...
hello all,
I am using nRF52832 and blow is my querry.
Implementation of power ON/Off feature:We are able to put the board to system ON low power and System OFF low...
I am using radio notification to change every advertisement packet. Here is my code:
static void on_ble_radio_active_evt(bool radio_active) {
if (radio_active) {
advertising_data_init...
Hi all!
I'm trying to move to SDK 14 with some project.
if NRF_SDH_BLE_GATT_MAX_MTU_SIZE = 23..70 all works good.
if NRF_SDH_BLE_GATT_MAX_MTU_SIZE > 72 exception happens...
Hello, I am investigating the possibility of integrating the DTM functionality into our app (which uses the softdevice) to allow us to use a single image for production testing...
Hi,
I am using the SAADC example in SDK 12.2.0 together with SoftDevice (S132, v3) and its working fine without any problems. As a modification, I want to uninitialise...
After calling sd_ble_gap_connect() at an arbitrary time, how does the central actually connects to the peripheral?
Assuming the client probably listens only at certain times...
Hi all,
Is there a way to change the UART pins configuration to bypass the segger jlink debugger on the nRF51/52 devices? I would like NOT to use this debugger chip for...
I am trying to receive a string of 708 characters via BLE. As BLE cap a maximum of 20 bytes per transmission, at the mobile app side I break the data to be send every 20 characters...
Hi All.
I wanna to continue Advertising during peripheral connection due connectable ADV prohibited if Peripheral connection established for nRF52840.
Is it possible to...
