Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
I'm using the nRF Connect SDK on nrf5340dk and encountering issues when trying to use the non-blocking (asynchronous) I2C API.
i am particularly getting this error - ENOSYS...
Hello,
I am running the NFC example applicaiotn(URI Message Example) in SDK5 v11.0.0. I am using a PCA10040(V1.1.1) dev board with the NFC antenna connected to it and testing...
We would like to use the nRF52 for an indoor application that should cover a a single family home.
The requirements for throughput are very relaxed, so we'd like to trade...
Hi Nordic,
I am trying to figure out the relation between a certain page number (say, 0xFE) and the group of addresses that it contains. How can I get this relation?
...
hi,
I am working with nr52832 and SDK 12.1.
I have referred the RNG example based on which I have integrated that code section in my custom application:
rng_generate...
I'm trying to accomplish a communication from the nrf24LE1 to the nrf24L01+. The nrf24L01+ is hooked up to an Arduino UNO. The nrf24LE1 is flashed with the "enhanced_shockburst_ptx_nrf24le1...
6.1.4 Erasing a page in code region 1
When erase is enabled, the NVM can be erased page by page using the ERASEPAGE register or the ERASEPCR1
register. After erasing a NVM...
Hello,
I was testing BLE Heart Rate Collector Example with two nRF52832 devices, one was programmed with ble_app_hrs_c as a BLE central role, and the other was programmed...
Hello everyone,
I have very pesky bug that is leaving me in fits. I have a feeling it is a timing issue, but I am not sure at this point. Here is my issue, and I would...
Hi Devzone.
I've taken the ble_app_hrs example,
and then added the example code from the PWM Driver example.
The PWM module is mostly functional,
however I have a...
Hi,
I'm trying to build a SPI Slave <-> BLE bridge, so that everything received over SPI bus is forwarded on BLE and vice versa. In order for the reverse direction to work...
Hello,
i think this is simple question, but nowhere i can find answer. Is nRF52840 preview development kit (PCA10056) contains built in nrf52840 microcontroller or i need...
I am going through the BLE Central tutorial and am a bit confused by the APPL_LOG function calls, from what I could understand it should give messages on serial port, like...
Hello, I have nRF51822 Beacon Kit (pca200006) and nrf51 dk board (pca100028)
I had an impression I could flash beacon and upload new files using nrf51 dk board as jlink over...
