Hi
I am trying to setup and test the OpenThread CSL feature on nrf52840DK with OpenThread daemon and RCP mode nrf52840DK.
I found there is a way to build the Daemon for...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
fail to erase an nRF 5340 DK. Can't recognize the COM. But board is recognized as J-Link driver. Does anybody know why this happen? the log is as follows:
2025-06-16T07...
hello all,
I'm fairly new to nRF SDF and its build environment. I browsed a lot of posts but did not find the solution to what is probably a basic misconfiguration error...
I am using NCS 3.0.0 and I want to generate keys ... But the method I am using to generate keys is giving me this error Here is the code where it is returning error:
psa_set_key_usage_flags...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
im using an external acceleromter to trigger an event once the device shaked. I configured the event pin on nrf51 EVENT_PIN as an input this way:
APP_ERROR_CHECK(acc_config_motion_detector...
Hi all,
I can able to blink led in mesh synchronously, but some time it fails in synchronization. when a new node enters into mesh it takes current mesh value, but for...
Hi all,
I am using ble mesh code for synchronizing leds in mesh network. I need mesh part, but itshould not integrated with version. So i can able change state of led,...
Hi,
I am a new programmer to the NRF51 and I was wondering if someone would look at my code. I am trying to program the NRF51 to take ADC samples at a frequency of 1 kHz...
I am using nRF52832 with SDK 11.0.0 and S132_V2.0.0 for my application. My beacon is inside Refrigerator where temperature varies from -2 to 20 degree .My Beacon code is in...
Hi,
I'm working on an application with S130 central (client) connecting to an Android peripheral device (server).
I have two characteristics on peripheral device, one...
Hi,
I would like to know what is the switching time between RX ShockBurst and STBY mode?
In documentation I can only find switching time between STBY -> RX ShockBurst...
I don't have a question but am rather posting the solution in case it helps someone else out who had the same problem as me.
With SDK v9/SoftDevice S110 v8, our application...
Hi guys,
I am really confused to distinguish SMP request from pairing request.
Could you kindly what the difference?
Device(nRF51822) can send SMP reqeust? If...
So, I've began tinkering with this device a bit, and using totally stock hex files, installed via
make flash_softdevice && make flash crashes bluez with sigsegv shortly...
I am struggling with the correct value to use for DFU_APP_DATA_RESERVED in the bootloader. My application uses the Device Manager and has one block allocated for to pstorage...
My app is generating hardfualts. Based on this post I looked at memory location SP + 0x14, which points to the address that generated the fault.
Memory at SP+0x14: 8F 31...
Hello Everyone,
I am doing the rough calculation of the power consumption of NRF51 where in the radio part of the datasheet it is indicating 10.5mA whether it is denoted...
Hello ,
I'm using a couple of nRF52 dev.board (one is Nordic preview dev.kit , the other one is a Rigado BMD-300) , with S212 ant+ softdevice . I'm able to deep-slepp the...
