Hello,
I am working on a project using the nrf5340 MCU, and I am using the ncs version v1.6.1. I need to use 7 data bits, 2 stop bits, and even parity for the serial port...
hello! I'm having problem when trying a repairing after clearing the bond information in the nrf52840 i using pairing via oob , i exchange oob between nrf52840 and RPI using...
Hi, I use the hci-uart sample (4.3.99) on an nRF54L15 board. The host is an esp. The setup seems to work fine, but every now and then the Nordic board gives an assert:
ASSERTION...
Does the EdgeAI module support running multiple models in parallel? For example, an anomaly detector running on one data source and a classification model running on a second...
i would like to implement multi pairing connection of 20 peripheral device by single central mode. Is it best solution to adopt multi NUS sample S/W in GIthub?
Hello,I am working with the nRF9151 SMA DK and I need the VDD_GPIO rail to operate at 3.3V to interface with some external components.
According to the schematics, VOUT1...
Hi,
I want to download FOTA-updates with HTTPS from a function app running on Azure. I am not using IoT hub or MQTT. I'm using modem firmware 2.0.4 in combination with version...
Hi,
I have install openocd on ubuntu. but i after running next line
openocd -f interface/stlink-v2.cfg cfg -f target/nrf51_stlink.tcl
i got these error.
Runtime...
Hi,
I'm trying to modify one of the examples (the hrs_relay) to find my custom service to identify the device uniquely. I know I need to add the 128bit uuid using and then...
I'm trying to transmit a radio signal inside time slot handler, the code is like:
switch (signal_type)
case NRF_RADIO_CALLBACK_SIGNAL_TYPE_START:
radio_configure...
I'm working with nrf52832 dev board. I used nRF Connect app for IOS but my phone run on IOS8.4.1, so i can't get it from apple appstore. Someone can help me by give version...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi there,
I'm using nrf51822 timer1 as the timer for some time-critical task, and I'd like to ask two questions about it:
What's the precision of Timer1 if the...
Hi
I am using nRF51822 (pca10001).I am unable to discover my device. I used the ble_app_template_s130_pca10028 as my base and added the code for gpiote handler as following...
Good day,
I tried the BLE Mesh Example located:
devzone.nordicsemi.com/.../
... and for some reason it is not working for me. I posted a comment where the example is...
Hi.
Faced with a strange situation.
Example. All look good when I read code area:
void ex1 (void)
{
uint32_t *addr_out;
uint32_t i,word;
addr_out=(uint32_t...
We've developed a custom board based on the nRF51822-QFAA and an MPU-6050 IMU. It runs on a li-pol battery and uses S110.
I've encountered a strange problem when power...
Hi,
I am working on measuring the voltage on a lithium battery (norminal 3.7V) with a voltage divider on nRF52832. The voltage divider combines a 510K and 360K resistor...
Dear Nordic Engineer,
I need to work on nRF52, my Macbook Air has OSX Yosemite 10.10.5 - I can run "make" or "nrfjprog" only if I copied libjlinkarm.dylib into the same...
We have a custom board using the ISP130301 BLE module (containing a nRF51822, 16MHz xtal, 32kHz xtal). Our apps work fine (gcc, SDK6, S110v7) except for high system on idle...
i don't see where the command queue index, m_op_queue.rp, is initialized.
when queue_process is called, the following line blows up:
fds_op_t * const p_op = &m_op_queue...
