Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
Our prototype is back. At first, I used NRF Connect to flash it, but the official PC software couldn't flash the firmware. I followed the wiring instructions: (1) connect...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Hi,
What happens if a user initiates DFU but never continues the process of uploading an image, does the device sit in this mode indefinitely long?
How might we implement...
Hi,
We're trying to port and migrate our nRF51 SDK v8 (softdevice s110) codebase to nRF52 SDK v11 (softdevice s132), but we're seeing a crash occur (goes into HardFault...
hello everyone:
I use nordic APPtoolbox to test DFU ,android toolbox can DFU,but ios toolbox can't DFU
1、 i use sdk9.0 dfu project,and sdk9.0 ancs project
2、 blog.chinaunix...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
Where to get Master Control Panel 3.4.0 source code? Our project is related to creating proprietary BLE profile's. We have some idea on how to program a sensor device...
Hi,
on my board I have a nRF51 and a LIS2DH accelerometer. I want to enable an interrupt pin INT1, so if the LIS2DH sends an interrupt event (pin change from high to low...
I am using example->peripheral->uart(KEIL version MDK 5) in SDK11.0 . Because my 52832 board is a new one I made, I changed RX_PIN_NUMBER and TX_PIN_NUMBER to 9 and 8. CTS_PIN...
Hi,I'm using mpu9150 imu sensor with nRF51822 EK kit, i want read that sensor values i.e acceleration, gravity, yaw,pitch,roll values in keil ide ,how i can do that? Can any...
Hi,i'm using the nRF51822 with the IMU 9150 sensor, i'm using the github.com/.../nrf5-mpu-examples git repo for my sensor. while i try to read the values of sensor in Tera...
I am trying to flash TCP-Server example from IOT SDK from Eclipse.
Project builds without errors.
But I am getting this warning message in Eclipse console when I flash to...
s130, nRF5_SDK_12.1.0_0d23e2a, SoftDevice 8_9_0.
I want to use the Central Glucose Service, how do i modify the "ble_central/ble_app_hrs_c" example code?
int main(void...
I wanted to use MQTT example with nrf52 DK board.
and I uploaded MQTT firmware which is located MQTT example folder in iot SDK.
www.youtube.com/watch
I tried to follow...
Hi,
I want to implement handler for undefined instruction fault. According to Cortex M4 documentation (ARM DUI 0553A subchapter 2.3.2 "Exception types") this fault leads...
Hi everyone,
I've been experimenting compiling my project with Clang and have run into some issues with the supervisor calls and their wrapper in nrf_svc.h.
Without...
Hi,
I want to implement simple module:
gpiote event on pin change (around 6.7MHz signal)
Route gpiote event through PPI to increment counter
Toggle GPIO pin...