Hi,
We are using nrf54l15 soc in our product and using NCS SDK 3.4.0. The LFCLK is set to SYNTH mode where it derives the clock from HFCLK. We have a crystal driving the...
NCS 3.0.1
nrf52840
nrf21540
I have read several tickets regarding antenna diversity and BLE. It does not seem to be supported for BLE. What about Thread?
I have read...
Affected: nRF Connect SDK v3.4.0; the same code is on main as checked on 2026-11-11 ( subsys/net/lib/nrf_cloud/common/src/nrf_cloud_codec_internal.c , subsys/net/lib/nrf_cloud...
We are currently using an NRF54L15 with TF-M on NCS 3.4.2. We have a custom secure partition, and want it to own a persistent P-256 ECDH private key and derived AES-128 key...
When I connect the two-pin battery and short pin1 and pin2 of P1, I am unable to get the battery voltage at J1 AND WHEN I LEAVE THE PINS UNSHORTED FOR P1, THEN I AM NOT GETTING...
I have connected the correct 47K res for VSET1 but I am not getting 1.8V, instead I am getting 2.3V I am getting the correct output for BUCK2 as 3.3V I have checked the resistor...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
NCS 2.6.0 nRF5340 project /ncs/v2.6.0/nrf/samples/matter/lock I want to enable APPROTECT on both app core and net core core. I want to enable it in firmware without UICR....
This question relates to using zcbor .
Basically I have the following.
I got The contents of FRAME - 00, 00, 00, 02, 00, 01, 01, 00, b0, 06, But I was expecting 00...
Hello,
we want to send a continous carrier with nrf9151 on dect-nr+ on a specific channel.
With bluetooth there is a testing option in nrfconnect tool.
Is there any...
Hi I would like some advice on where to start learning Nordic BLE?
All I could find by searching was advice from 6-9 years ago, I think today they are not relevant, because...
hello,
I'm doing a power consumption test, but I'm not sure which project to use to test the power consumption.I tried the "peripheral_lbs" download with NCS version 2.8...
My setup: SDK version: 2.5.0.v Modem version: 1.3.0. I am using MQTT to subscribe to a topic, for example, the LED state. The plan is t o set the LED state on the server side...
Hello, thanks for reading and happy holidays!
We are using an nrf5340dk, with zephyr and SDK 2.5.0.
We seem to have two undesired behaviors from MCUBoot immediately after...
Can,t flash nRF52832 custom board using nrf connect vscode extension im trwing to use nRFconnect for my project, im using fade_led from example and got this error
i try...
Hi everyone, I have a problem when I tried to configure UART ( baudrate, parity, data_bits, stop_bits, flow_ctrl). I upload my project:
#include "myuart.h"
#include...
Hi,
I want to use nRF9160's internal RTC. I coded it but did not get the real time correctly.
SDK: 2.5.0
IDE: vs code
board: nRF9160dk
Best regards,
Liza
I'm going through the Academy courses and somewhere around Lesson 3, I could no longer flash firmware to the nrf52840 DK.
I browsed the forum and found some notes around...
nrf connect for desktop nrf54l15 device not detected by bluetooth le app
log:
12:18:38.872
Using nrf-device-lib-js version: 0.4.4
12:18:38.872
Using nrf-device...
Hi,
in Cellular Iot Fundamentals there is in lesson 4 an exercise to move to MQTT with TLS.
As I used MQTT helper library, I wonder if it is enough to modify the structure...
We had an issue with the FDS such that if the device lost power in the ~50ms window after bonding was carried out, the FDS would take longer to initialise when power was restored...
