Subject: nRF9151 – EU coverage of mfw 2.0.2 and antenna gain (Schréder Sense One)
Dear Nordic
I'm working on CE and RCM certification for Schréder's SENSE ONE smart-city...
We have an nRF54L15 (QFAA) board, acting as an I2C target ( TWIS30, P0.00/P0.01, address 0x42, 100 kHz ) for an ESP32-S3 through a TCA9406 level translator.
Flow:
Between...
Hello, I am requesting a schematic review of my bluetooth microphone system. I've used the spec sheets as well as audio DK hardware reference material to design these schematics...
We are seeing very high defect rate when installing this part on boards: insufficient solder, solder bridging. When we look at the pads under the microscope, we are seeing...
Hello,
We have an issue. Our device is a custom board based on the nRF9151, and we use it in Latvia. Two network providers are available for our Onomondo SIM card: one supports...
Hello,
We are developing a product based on the nRF52840. According to the blog post nRF Connect SDK gets Long-term support with version 3.4.0 , NCS v3.4.0 declares the...
Subject: Request for Optimal Battery Solution for nRF54L15 Matter End Device
Hello DevZone Team,
I am opening this ticket to identify the optimal power solution for my...
I want to interface 3 custom made heater boards to nrf5340dk. Where the simple task is to toggle gpio's to Turn ON & OFF the heater board. Now, we are using P 0.01, 0.02 &...
Hello, I am considering the prospect of using channel sounding as opposed to UWB for indoor asset tracking. I can understand, that the main limitation with that would be,...
Hi There:
I used the nRF7002 DK to evaluate its WiFi throughput performance.
The test environment is below:
1. nRF7002 DK
2. NCS version: 2.5.0
3. Sample application...
Hello Everyone,
I have configured SPI1 at 1MHz, to receive data with a sensor. Basically i am reading data from a sensor device. So calling spi_transceive_dt() with 4...
hey i am using a custom nrf52840 board and i keep my device on by setting a gpio pin high and device turns off as soon as it sets to low .
during ota update when the bootloader...
Hi,
I have a firmware project that was originally developed for an nRF52833. It successfully mounts LittleFS on 3 partitions in external flash. For the nRF52833 I was simply...
Dear Devzone!
I am trying to add AES-128 decryption support for secure DFU with cc310_bl backend. However when I call nrf_crypto_aes_update it never returns. Examining the...
Hi all,
I started encountering the error shown in the attached screenshot.
From the this PR , it seems the issue is new and that the PR is aimed at resolving it. However...
Hi,
I'm developing a BLE Central using a nRF52840 DK. My project goal is to analyze the quality and the robustness of a peripheral's BLE connection.
For some parts of...
Hai, I develope the nrf52810 based product I need work BLE Communication with Bonding connect multiple nrf52810 device connect to the nrf52832 Using Zephyr. Regards, Praveen...
We are using SDK v2.6.1 for our application and would like to search for nearby Wi-Fi networks using the nRF7002-DK.
Could you please assist us with this? If any reference...
Hello.
In the BLE software being developed, the device uses nRF52840, s140 v7.2.0 or v7.3.0, and I am building a system that periodically sends a beacon (ADV_NONCONN_IND...
As the title suggests, I'd like some help reviewing my schematic for a 52832 pcb. I have tried to stay as close as possible to the DCDC reference design. Some notes on the...
I'm adding DFU over Bluetooth support to an existing application based on nRF Connect v2.3.0 following these instructions . What the instructions lack (and possibly is a given...
