I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
Hi
SDK: ncs-v3.4.2
I wanted to compile the lesson as a starting point for a product in non-secure mode with TFM.
I don't have the nrf5340dk but one with the same chip...
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
Hardware: nRF21540 DK
SDK Version: NCS 3.4.0
Problem Description:
Modified the observer sample to scan for a specific device, using nRF21540 DK as the scanner with FEM...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Greetings,
in Visual Studio code the project workspace looks ok. However NRF Connect is not able to see the application. The error message is of no help:
This did...
Hi everyone!
My name is Natalia, and I’m just starting to work with Nordic. This is my first design, and I’m trying to connect the nRF7002 module to the nRF52840 microcontroller...
I need to match the 50 ohm impedance for antenna performance. It would be easier to manufacture using 4 layers, but I'm planning to manufacture it in 2 layers due to cost...
We are working on product to combine esp32(wifi chipset)+nrf52840(ble, thread and matter ) we wants to keep it as matter device + matter controller to have its seprate network...
We are finishing up our certification process and to complete Wifi Adaptivity, we need to operate the Wifi Shell sample . However, we need to do it on top of our custom board...
Hi,
ncs\v2.8.0\nrf\samples\esb
1. Based on this example, how can customers achieve the frequency modulation function 2. What are some examples for reference? 3. What frequency...
I used this direct test mode sample project: "ncs\v2.6.1\nrf\samples\bluetooth\direct_test_mode"
I can connect and test it normally on the nRF5340 development board with...
Hi,
I am currently using the NRF52840 in a 2 MCU setting (2nd MCU is from STM). UART0 is connected to the PC while UART1 is connected to the second MCU for communication...
I'm using nRF Studio Visual Studio Code. (SDK and Toolchain v.2.7.0) with the nRF7002 Development Kit. The Blinky example have worked fine and also the other things as shown...
I'm trying to run the vanilla HTTPS sample on the nRF9161 DK: sdk-nrf/samples/net/https_client/README.rst at 4b9841a28e97e9d61b93f8981375d644b9d04ea0 · nrfconnect/sdk-nrf...
I need to install the Direct Test Mode App to validate the direct test mode running on a custom board. On the version 5.1.0 of nRF Connect for Desktop all app installations...
Hi everybody I'm using nRF Connect SDK 2.6.1. I have my own board based on nRF52840 SoC. I made an overlay file of nRF52840DK and changed its UART TX/RX settings according...
I am trying to use my nRF52840 as a sniffer and am attempting to follow the directions at:
Programming the nRF Sniffer firmware (nordicsemi.com)
Note that I have downloaded...
Hi,
I want to use a LNA for make our sensitivity better, Then i should to put a RF switch and have a control in sending and receiving, because when the device is in receiving...
