Hi,
I have B0, mcuboot and then application as my partitions. We plan to support upgrade of both mcuboot and application.
Based on this below Kconfig snippet, it looks...
Should sdk-zephyr carry this ring-buffer adaptation or adopt the newer upstream receive implementation from github.com/.../122772
At sdk-zephyr `3876d730`, RX BUSY remains...
Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hello I'm developing a project that would communicate with a cellular module using AT-Commands, and voice data using PCM, these cellular modules are always using PCM Short...
What high-temperature storage (JESD22-A103) and temperature-cycling conditions was the nRF9151 qualified to (temperature, duration, cycles)? Your DevZone forum mentions 125...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
Problem:
After every wake-up our device reports a SoC 10–28 % higher than it reported just before going to sleep.
Between sessions the nRF5340 is in System OFF via sys_poweroff...
Dear Nordic team,
I am trying to set up OTA updates by using the DFU target API on an nRF9151 DK with MCUboot and TF-M partitions. (NCS v3.4.1) My goal is to use the immutable...
Hi,
GSMA SGP.32 v1.3 section 3.8.2 and 3.8.4: the device selects IPAd or IPAe mode with the TERMINAL CAPABILITY command at UICC initialisation. Tag 84 , byte 1, bit 1 set...
Hi,
I am going nuts with the device tree replacement for PM that seems to cover about 1 case out of a larger number of possibilities. Please give me the overlay files and...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hello,
Could Nordic clarify the supported deadline and recovery behavior of pcd_network_core_update() when the network core never changes its command status?
At sdk-nrf...
Hello!
We have a nRF52832 firmware project on NCS v3.4.1. After recently moving from NCS v2.9.0 we saw small current spikes every 1s (roughly) in our idle state, which weren...
hi team,
i have trying to wrote a code for adc module in segger 5.40 using nrf52840 controller and i found you mentioned different frequencies for each pins in datasheet...
Target device: nRF9151
NCS 3.4.0
Memfault Integrated
FOTA architecture in place with four slots, 2 in internal flash and 2 in external flash
Background COAP updates...
Hi Nordic Team,
I'm debugging an unexpected software reset on an nRF54L15 running nRF Connect SDK v3.4.0 . BLE FOTA through MCUmgr completes successfully and the new image...
I've trying to get MCUBOOT woth work with my project & after much time/effort & found my project, untoughed, works on the nrf52840DK. I then discovered that the mcuboot build...
Hi Nordic team,
While benchmarking quantized INT4 (`s4`) matrix-vector multiplication (`arm_fully_connected_s4` / `arm_nn_vec_mat_mult_t_s4`) on an **nRF54LM20 DK (`nrf54lm20dk...
Hi,
We are designing a battery-powered product based on two Nordic chips and would like your recommendation on the overall architecture before we freeze the hardware, having...
I'm aware of https://devzone.nordicsemi.com/f/nordic-q-a/125252/reset-over-ctrl-ap/555253?focus=true
Is it possible for an nRF54 to safely use the CPU access to the AP registers...
