Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
SPIM00 SPI transfers return all zeros on nRF54L15 with NCS v3.3.0 0

Board: Custom board based on nRF54L15 NCS Version: v3.3.0 SoC: nRF54L15, revision 2 Toolchain: nRF Connect SDK v3.3.0 bundled toolchain Problem Description SPIM00 on nRF54L15...
28 views

0 replies

Started 1 hour ago
by Aasim_
Not Answered
GRTC after reset 0

Hi, I am developing an application for the nRF54L15 using NCS v3.2.4 , running entirely in the Secure domain . My goal is to maintain a continuous hardware system time...
15 views

0 replies

Started 1 hour ago
by omt
Not Answered
dfu issues after migrating from ncs2.9.2 to ncs3.0.2 0

hello Nordic we are working with nrf52840/nrf52832 with ncs (currently on v3.0.2) i have noticed that when i try to dfu a merged artifact of my version with the new mcuboot...
- development
- software
- nRF Connect SDK
- zephyr
- nrf52840
- dfu
16 views

0 replies

Started 2 hours ago
by ziv123
Not Answered
How to integrate the Edge Impulse SDK into an ncs3.3.0 project to run EI models 0

I have installed ncs3.3.0 and want to keep ncs unaffected. According to the document docs.nordicsemi.com/.../sdk_setup.html , I should choose to import the edge impulse SDK...
19 views

0 replies

Started 4 hours ago
by llly
Not Answered
Does nRF54L15 support BLE stable modulation characteristics at 1Mb/s & 2 Mb/s..., if we meet related issue, how to debug on HW and SW side? 0

Dear Nordic Team and Distributors, For nRF54L15 (CSP and QFN) design circuits, how to optimize the stable modulation issue? What aspects should we consider to do failure...
25 views

0 replies

Started 5 hours ago
by gengyuanfa

Recent in the DevZone Blog

Optimizing Power on nRF52 Designs

notsane0

As customers reach the end of their design cycle, their attention generally falls on power optimization, especially for battery powered designs. The following are hints for achieving the lowest possible…
- 30 May 2018
New Smart Remote 3 SDK release enables cost optimized Bluetooth 5 voice remote controls

Pär H

It has been some time since we released new SDK for the nRFready Smart Remote 3 for nRF52 Series. The recently released rev 1.2 of the firmware introduces a lot of new features and improvements. This SDK…
- 24 May 2018
Accurate State of Charge Measurements For Li-Ion Batteries Using a State of Charge vs Open Circuit Voltage Lookup Table

Bjørn Kvaale

We have had a few questions on the Nordic DevZone related to state of charge estimation of Li-Ion batteries when used in conjucture with an nrf52 DK. This blog post will show you how to customize your…
- 14 May 2018
Testing Long Range (Coded PHY) with Nordic solution (It Simply Works)

Susheel Nuguru

**Project and hex files for testing this is attached in the end of this blog. Introduction There has been a lot of discussion/testing/confusion about testing the long range feature of Bluetooth Low Energy…
- 2 May 2018
Introducing experimental release of Programmer Application

Reidar Martin Svendsen

nRF Connect for desktop has proven its flexibility by being cross platform and ability to install and update applications based on users need. Motivation Our initial goal was to modernize and cover…
- 30 Apr 2018
New in nRF5 SDK v15: Strong Hardware-Based Security with Infineon OPTIGA Trust X

ChristianLesjak

Defining a business model and implementing a technical infrastructure are two major phases in building a successful product or IoT system. However, protecting the business model and your customer’s data…
- 9 Apr 2018