Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. 0

nRF52810 board will not start on its own. It needs the RTT Viewer to be connected, then it will start and run. It has run on its own before with this configuration: CONFIG_CLOCK_CONTROL_NRF_K32SRC_RC...
11 views

0 replies

Started 29 minutes ago
by epolicar
Not Answered
BLE antenna switching on/off while transmitting 0

Hello, We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
- Evaluation
- antenna
- nrf52832
- bluetooth le
- ant
- rf design
- hardware
20 views

0 replies

Started 1 hour ago
by xinyangt
Not Answered
How to software-switch between ESB and BLE on a nrf5340 net-core? 0

Hi, I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
22 views

0 replies

Started 4 hours ago
by nfbe
Not Answered
Emulating Xinput, what are the requirements? 0

Hello, I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
- development
- software
- nrf52840
- usb
24 views

0 replies

Started 5 hours ago
by blitz0145
Not Answered
CMakePresets.json broke in new nRF Connect for VS Code version 0

Hi We are using the CMakePresets.json file for different variations of our firmware. Since the latest update (2025.4.106) the build configuration interface changed a bit...
26 views

0 replies

Started 8 hours ago
by AlanIoT

Recent in Nordic blog

Reproducible build environment for nRF52 using Rebuild (rbld.io)

Yaniv Nis

As you probably know having a build environment, you can replicate and deploy with ease has the potential to save a lot of R&D time. If you can also control its versioning so you would be able to "get…
- 31 Jul 2017
Flashing and Debugging nRF51/52 with a cheap blackmagic probe compatible SWD programmer

Mahesh Venkitachalam

When we built our Bluey nRF52 BLE dev board, we were looking for an inexpensive option for our users to upload code to bluey and debug it using ARM GDB. We then came across the blackmagic probe (BMP…
- 24 Jul 2017
Introducing nRF5 SDK for Mesh

esivertsen

The day after the Bluetooth SIG announced the 1.0 spec of the Bluetooth mesh we are happy to announce the nRF5 SDK for Mesh for our nRF51 and nRF52 Series SoCs. This first (v0.9.1) release is packed with…
- 20 Jul 2017

Latest guides

Getting Started: Developing for the nRF52805 with nRF5 SDK

bjorn-spockeli

Introduction The nRF52805 SoC is a low-cost member of the nRF52 Series with a subset of the features of the nRF52811 and nRF52810 SoCs. As the nRF52805 has a feature subset of the nRF52810/11 SoCs, which…
- 11 Jun 2020
nRF5x: nRF52832 Specific PCB Guidelines

Andreas

This guide will cover the specific areas that must be paid extra attention to when designing a PCB for nRF52832. It is intended as a nRF52832 specific addition to the General PCB design guidelines for…
- 10 Jun 2020
Hardware design, RF test and coverage: iBasis eSIM International Coverage Update

Brian Kim

Since Nordic Semiconductor announced that it has partnered with one of the world’s largest international cellular carriers, iBASIS, to use nRF9160 System-in-Package (SiP) module and to include an iBasis…
- 4 Jun 2020
Getting started: Getting NB-IoT Demo running on Thingy:91

Christian Kurz

The Nordic Thingy:91 is a cellular IoT prototyping platform. It is based on the nRF9160 System-in-Package (SiP). The nRF9160 has an integrated modem that supports both LTE-M and NB-IoT. The factory programmed…
- 29 May 2020
Bluetooth low energy: Mocking CoreBluetooth

Aleksander Nowakowski

CoreBluetooth is the native iOS framework to communicate with Bluetooth-enabled Low Power (LE) devices, except iBeacons (which require CoreLocation) and HomeKit devices. It is easy to start with, if one…
- 9 Mar 2020
Getting Started : Build NCS application firmware images using Docker

Markus Tacker (he/him)

How to compile a NCS application using Docker so you don't need to install dependencies directly in your system.
- 17 Feb 2020