Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
WIFI SoftAP + Station mode in one compiled image 0

nRF54LM20 + nRF7002, NCS 3.4.1: SoftAP provisioning and station low power in one image Our battery-powered product (no BLE antenna), removed due to space in the PCB and...
53 views

0 replies

Started 1 day ago
by SubuMuthu
Not Answered
Energy consumption in NTN mode vs LTE-M 0

Hi Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M? In particular I am curious if NTN has...
43 views

0 replies

Started 1 day ago
by ovrebekk
Not Answered
Can’t generate ncs-sbom with nRF Connect SDK v3.1.1 0

Hello. When I ran the NCS SBOM command using VS Code, the following error occurred, and the file could not be generated. I would appreciate it if you could tell me how...
51 views

0 replies

Started 1 day ago
by Fumiya
Not Answered
Title: nRF54LM20 DK debug-out (P13) reset line holds an external nRF52840 target in reset after a pin reset or CTRL-AP hard reset 0

Setup - Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
60 views

0 replies

Started 2 days ago
by dm1
Not Answered
LED doesn't blink on nRF54L10 custom board connected to nRF54L15-DK 0

I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09. #include <zephyr/kernel.h> #include <hal/nrf_gpio.h> ...
60 views

0 replies

Started 2 days ago
by Star0

Recent in the DevZone Blog

How to build continuous integration and delivery process for embedded SW development

Yaniv Nis

If automated testing, continuous integration, and delivery processes are top of mind for you, but you are not sure how to start implementing it for embedded SW development - take a look at the following…
- 3 Oct 2017
Multiple channels in RTT

Krzysztof Zaraska

Segger RTT (Real-Time Terminal) supports multiple data channels. RTT Viewer uses channel 0 only, and implements multiple virtual terminals on top of this. The terminal can be switched by SEGGER_RTT_SetTerminal…
- 29 Sep 2017
6 Things to Know about Bluetooth Beacons

Rose Martin

Smartphones and tablets have revolutionized the manner in which people communicate with each other. Mobile applications with location-based features like Bluetooth beacons, WiFi, and GPS are helping people…
- 22 Sep 2017
Creating a Keil project for a Bluetooth Mesh example (Updated for 0.10.0)

Kristian Skordal

Introduction The recently released nRF5 SDK for Bluetooth Mesh does not provide Keil project files for its example projects. Fortunately, it's relatively easy to set up your own project from scratch.…
- 19 Sep 2017
Using millis() like in Arduino.

schef

Here are two simple functions to use when you want to use timestamps for time measurement. uint32_t millis(void) { return(app_timer_cnt_get() / 32.768); } and for comperison of current with given…
- 18 Sep 2017
Flashing nRF5x firmware using any dumb terminal program via standard serial COM port

Nguyen Hoan Hoang

There are times that we needed to flash the nRF5x series on a PC where the development software were not installed. The problem could be worst when network access is limited. With a HEX file on hand…
- 18 Sep 2017