Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Illegal use of the EPSR - uart fault
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hi, i have some code thats based off of the uart_async_adapter.c example code. I' m getting a `usage fault` which i've traced to uart_irq_handler. it happens when i try...
- development
- software
- zephyr
- nrf52832
0 views

0 replies

Started a few seconds ago
by michaelmac
Not Answered
Error[Pe020]: identifier "NRFX_RTC0_INST_IDX" is undefined
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hi, In trying to take the PPI example code from nRF5_SDK_17.1.0_ddde560 and adapt it to use RTC for an event-end-point, I get the following error: Error[Pe020]: identifier...
20 views

0 replies

Started 1 hour ago
by Matt_V
Not Answered
unable to flash on bt 40
View Voters Login to vote on this thread 0 Login to vote on this thread
0

-- west flash: rebuilding [0/16] Performing build step for 'tfm' ninja: no work to do. -- west flash: using runner nrfjprog -- runners.nrfjprog: reset after flashing requested...
16 views

0 replies

Started 2 hours ago
by lalith88
Not Answered
Pushing keys from KMU to ECB?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hi! I'm storing a key in the KMU for use by the ECB. If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
22 views

0 replies

Started 3 hours ago
by SebastianA
Not Answered
Issue of nRF54L15’s GPIO high voltage is lower than VDD
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Hi Support Team The VDD of customer’s nRF54L15 board is 3V, but the high voltage of P1.10 is about 1V. Did you meet this issue before? Customer needs the output high voltage...
17 views

0 replies

Started 3 hours ago
by Tom.Fu

Recent in Nordic blog

6LoWPAN for Bluetooth low energy on OpenWRT

Glenn Ruben Bakke

OpenWRT is one of the most popular open source Linux-based router firmware alternatives for commodity routers. From kernel 3.17, Linux has supported 6LoWPAN for Bluetooth low energy (BLE) through the…
- 13 Mar 2015
IPv6-Brewed Coffee Over Bluetooth Smart

Glenn Ruben Bakke

Believe it or not, the day has come when your coffee machine could know what exactly what kind of coffee you like to drink depending on the cup you’re using, the time of day, and a multitude of other…
- 4 Mar 2015
Debugging Arduino project with Atmel Studio

Stefan Birnir Sverrisson

When using nRF8001 with an Arduino board, Atmel Studio is a good free tool to use for development of your firmware. The following video shows a procedure in Atmel Studio in order to enable debugging of…
- 19 Feb 2015

Latest guides

Software and Protocols: Automating nRF91 TLS credential management via serial port AT commands

Daniel Veilleux

I have spent a bit of time recently experimenting with different TLS credential configurations using nRF91-DKs. Eventually I got to the point where I wanted to do things like swap out the certificates…
- 10 Jan 2020
Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019

Nordic DevZone

Illegal use of the EPSR - uart fault View Voters Login to vote on this thread 0 Login to vote on this thread 0

Error[Pe020]: identifier "NRFX_RTC0_INST_IDX" is undefined View Voters Login to vote on this thread 0 Login to vote on this thread 0

unable to flash on bt 40 View Voters Login to vote on this thread 0 Login to vote on this thread 0

Pushing keys from KMU to ECB? View Voters Login to vote on this thread 0 Login to vote on this thread 0

Issue of nRF54L15’s GPIO high voltage is lower than VDD View Voters Login to vote on this thread 0 Login to vote on this thread 0

Illegal use of the EPSR - uart fault
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Error[Pe020]: identifier "NRFX_RTC0_INST_IDX" is undefined
View Voters Login to vote on this thread 0 Login to vote on this thread
0

unable to flash on bt 40
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Pushing keys from KMU to ECB?
View Voters Login to vote on this thread 0 Login to vote on this thread
0

Issue of nRF54L15’s GPIO high voltage is lower than VDD
View Voters Login to vote on this thread 0 Login to vote on this thread
0