Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
LIS2DH12 Sample Not Working on nRF54L15-DK — "Device LIS2DH is not ready" 0

Hi everyone, I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
5 views

0 replies

Started 21 minutes ago
by DennisDG
Not Answered
Dynamic BLE TX Power Config Fails (nRF5340-DK) 0

Hello everyone, I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
18 views

0 replies

Started 2 hours ago
by diegonovo02
Not Answered
Power profiler Kit II for NRF54L15 0

Hi, When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
18 views

0 replies

Started 5 hours ago
by NickDeLeenheer
Not Answered
How to configure a custom nrf5340 board with HV and DC-DC and a VREGH 3.0V output 0

I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it. I see the documentation on REGULATORS — Regulator control where...
16 views

0 replies

Started 5 hours ago
by lcj
Not Answered
conflicting CPU architectures 17/2 0

Hi, NRF54L15, nordic sdk version 2.9.1 I recently lost ability to build my application. I get this linker error: /home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
17 views

0 replies

Started 7 hours ago
by Adam W

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018