Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Does nPM2100 support CR123A 1S2P? 0

Hi Sir, As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) . But could nPM2100 support CR123A 1S2P? ...
11 views

0 replies

Started 2 hours ago
by Hsu
Not Answered
Error when flashing nrf5340 custom board in HV DC/DC mode with 3V0 set using a segger jlink plus 0

I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
19 views

0 replies

Started 8 hours ago
by lcj
Not Answered
Unable to Create New Build Config in nRF Connect (NCS 3.0) – “Add Build Configuration” Always Fails 0

Hi, I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
20 views

0 replies

Started 8 hours ago
by witc
Not Answered
Question Regarding Current Measurement on the nRF52840 DK (P22 Header) 0

Hello, Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project. I am working with the nRF52840 DK, and I am trying...
19 views

0 replies

Started 10 hours ago
by Tubald
Not Answered
Can not receive periodic advertising reports nrf52833 0

Hi, I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone). I am using bindings to the softdevice controller ( https://github...
22 views

0 replies

Started 10 hours ago
by Tomer Eliahu

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018