Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Using nrfutil sdk v2.9.3 fails under Windows "class must define a '_type_' attribute" 0

Hi, After installing nrf sdk v2.9.3 trying to build application under Windows fails with the following message: Trying to run any command inside the NCS shell/terminal...
3 views

0 replies

Started 6 minutes ago
by Andrei H.
Not Answered
nRF5340 BLE Audio Request for Schematic Review 0

I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
- auto_pmic
- Evaluation
- nPM1100
- auto_le_audio
- auto_bluetooth
- bluetooth le
- auto_nrf5340
- low-power
- rf design
- hardware
- auto_hardware
- nRF5340
58 views

0 replies

Started 12 hours ago
by DavidMorina103
Not Answered
b0 fails to boot using swap algorithm in SDK 3.2.1 in nrf5340 0

Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
43 views

0 replies

Started 13 hours ago
by AlejandroM
Not Answered
BLE disconnect reasone 8 0

Hi everyone, I'm using the nRF5340 on a custom PCB board without an external 32 kHz oscillator. On the network core I flashed the hci_ipc sample. For some reason I occasionally...
51 views

0 replies

Started 14 hours ago
by Petar02
Not Answered
DECT NR+ rssi-1 measurement results saturated 0

Hello, I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware. The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
37 views

0 replies

Started 15 hours ago
by dame

Recent in the DevZone Blog

Setting up Segger on a mac or pc and debug - step by step for humans

Lola

Most guides out there are unclear and made for machines. Here is a full guide how to setup Segger for mac OS X with some example project from the SDK ( or even a PC but not tested), and also how to debug…
- 5 May 2017
FreeRTOS threads preview with J-Link, GDB/Eclipse

Radoslaw Koppel

Short note how to make FreeRTOS program debugging with eclipse little simpler. If you are looking the information how to configure the whole environment see this post: https://devzone.nordicsemi.com/tutorials…
- 11 Apr 2017
Taking a deeper dive into Bluetooth 5

esivertsen

The first in a series of blogs that will help educate on what is most important about Bluetooth 5 and take you deeper into the details of how it works and how you can benefit most from using it. Taking…
- 7 Apr 2017
Logging enabled by default in SDK Bluetooth examples

Håvard

Several users have pointed out a sudden flash size increase in some of our Bluetooth examples. We decided to write a quick post here to describe the reason for this and explain how to decrease the size…
- 29 Mar 2017
Monitor Mode Debugging with J-Link and GDB/Eclipse

Daniel Veilleux

The biggest pain point when debugging an application on the nRF51 series is the inability to set breakpoints while the SoftDevice is active without triggering an assert. Although a workaround exists that…
- 29 Mar 2017
Throughput and long range demo

ovrebekk

The new Bluetooth 5 specification promises twice the speed and 4 times the range. Doubling the speed is achieved by increasing the on-air datarate to 2Mbps, while quadrupling the range is achieved by lowering…
- 28 Feb 2017