Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
Scene Save Issue – Blind Position Not Visible in Scene Configuration 0

While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene. Steps...
30 views

0 replies

Started 3 hours ago
by Harsh0
Not Answered
nRF54L15 LFRC calibration current consumption during System ON low-power mode 0

Hi Nordic team, I am working on a custom board based on the nRF54L15 using nRF Connect SDK v3.1.0. On our hardware, the nRF54L15 has a 32 MHz crystal connected to XC1...
23 views

0 replies

Started 4 hours ago
by Mike012
Not Answered
SLM XSLEEP: Automatically wake UART on incoming URC/SMS/UDP event? 0

Hello, I am using the nRF9151 DK with the Serial LTE Modem (SLM) application. I put the device into sleep mode using: AT#XSLEEP=2 This successfully disables the UART...
24 views

0 replies

Started 5 hours ago
by Hassan0
Not Answered
nRF54L15 SDC ASSERT 131,1143 (sdc_assertion_handler) on Channel Sounding reflector when procedure uses antenna config A2_B1 (2:1) 0

Environment - SoC / board: nRF54L15 on Ezurio BL54L15U DVK (board target bl54l15u_dvk/nrf54l15/cpuapp) - nRF Connect SDK: v3.3.1 - SoftDevice Controller build: v252.31313...
41 views

0 replies

Started 5 hours ago
by Michael Chen
Not Answered
Questions on nRF54LM20-CAAA (CSP61) hardware design 0

Hello Nordic team, We are reviewing our nRF54LM20-CAAA (CSP61) hardware design and would appreciate your clarification on several power and RF related points. DECRF...
33 views

0 replies

Started 8 hours ago
by zhanxy

Recent in the DevZone Blog

Developing Nordic nRF51 applications with mbed and Visual Studio

ivan

This tutorial shows how to use the mbed framework to develop applications for Nordic nRF51 devices. Before you begin, install VisualGDB 5.1 or later. Start Visual Studio and open the VisualGDB Embedded…
- 26 Jan 2016
PA / LNA support in S132

Einar Thorsrud

The S132 SoftDevice for the nRF52 has support for enable/disable switching of external Power Amplifiers (PA) and Low Noise Amplifiers (LNA) using GPIO pins. This was introduced in S132 version 2.0.0-7…
- 25 Jan 2016
Step by Step Guide to Setup and Start Developemt with nRF51 or nRF52 DK and IAR

Pratyush Dave

The purpose of this blog is to provide a step by step guide to help a developer, starting off with the Nordic Semiconductor nRF51 DK, to get the necessary tools installed and get the software (SW) development…
- 25 Jan 2016
BLE nrf51 - Multilink NUS central - Connect to many peripherals through NUS service - with Arduino host

Marco Russi

Hi all, I implemented a simple multilink NUS central based on s130 for nrf51 chip-set. It means that this NUS central can connect to several peripherals simultaneously and send data to each one of them…
- 24 Jan 2016
SEGGER Embedded Studio Part 2 - Monitor Mode Debugging

Michael Dietz

This tutorial will take less than 15 minutes. #Motivation Never lose a BLE connection when debugging your applications again! This technique will also be useful for any application using the PWM peripheral…
- 22 Jan 2016
An introduction to error handling in nRF5 projects

Audun

As you start developing with the nRF5 series chips, SoftDevices, and SDKs, it's very useful to learn how errors can be discovered (and preferrably recovered from). This can be detecting something as simple…
- 20 Jan 2016