Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF5340 BLE Audio Request for Schematic Review 0

I am designing an ultra-low-power BLE Audio TWS board based on the nRF5340 and have followed the recommended hardware design guidelines throughout the project. This is my...
- Evaluation
- nPM1100
- bluetooth le
- low-power
- rf design
- hardware
- nRF5340
50 views

0 replies

Started 9 hours ago
by DavidMorina103
Not Answered
b0 fails to boot using swap algorithm in SDK 3.2.1 in nrf5340 0

Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
36 views

0 replies

Started 9 hours ago
by AlejandroM
Not Answered
BLE disconnect reasone 8 0

Hi everyone, I'm using the nRF5340 on a custom PCB board without an external 32 kHz oscillator. On the network core I flashed the hci_ipc sample. For some reason I occasionally...
44 views

0 replies

Started 10 hours ago
by Petar02
Not Answered
DECT NR+ rssi-1 measurement results saturated 0

Hello, I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware. The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
29 views

0 replies

Started 11 hours ago
by dame
Not Answered
DPPI and GPIOTE BLE events on nRF54L15 0

Hi all, I'm working on BLE time synchronization between nodes using hardware timestamps via GRTC + DPPI + PPIB cross-domain. CRCOK and PHYEND work perfectly, but adding...
55 views

0 replies

Started 13 hours ago
by ArneVds

Recent in the DevZone Blog

Nordic's infocenter

Oisin

The Infocenter – our new documentation portal - has now been up and running since June and contains all of our technical documentation. We saw the need for this because we wanted to make our complete…
- 24 Aug 2015
nRF51822 now supports extended industrial temp range (-40 – 105C)

Pär H

We recently announced that we now support “extended industrial temperature range” (-40 – 105C) on our nRF51822. The devices supporting -40 - 105C are the QFAA (QFN with 256kB flash and 16kB RAM) and the…
- 24 Aug 2015
Running micro-ESB concurrently with BLE

Audun

Introduction Using proprietary protocols can be an effective way of addressing shortcomings in BLE. When communicating between two nRF chips, one can for example use a different packet format or different…
- 14 Aug 2015
FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015