Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
AT+CFUN=20 (lte_lc_func_mode_set DEACTIVATE_LTE) blocks indefinitely under registration churn — software deadlock ruled out (nRF9151, mfw 2.0.4, NCS 3.3.0) 0

Environment nRF9151 (Thingy:91X), modem firmware mfw_nrf91x1_2.0.4 nRF Connect SDK v3.3.0 (Zephyr 4.3.99) LTE-M + GNSS: CONFIG_LTE_NETWORK_MODE_LTE_M_GPS=y PSM requested...
13 views

0 replies

Started 25 minutes ago
by Edemusmax
Not Answered
I2C clock stretching nRF54L / Zephyr 0

This is nRF54L10 with Zephyr, SDK & toolchain both v3.02 on a custom board. I am investigating I2C crashing on the 54L10. This happens during writing data to a MAX41462...
12 views

0 replies

Started 35 minutes ago
by Nick_RA
Not Answered
nRF52840 Oscillator not working 0

Hi, We have designed a custom nRF52840 development board based on the XIAO nRF52840 reference schematic. We connected a J-Link debugger to the board and are able to successfully...
33 views

0 replies

Started 5 hours ago
by Aditya P
Not Answered
nRF5340+nRF7002: Unable to trigger FOTA download error event after WiFi network disconnected 0

Hi, We have a device using nRF Connect SDK v3.0.2. The issue is when we try to do FOTA download and we disconnect the WiFi network (power down the router AP) while it...
42 views

0 replies

Started 12 hours ago
by Winston A
Not Answered
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board works on DK 0

# nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board -works on DK ## Summary On a custom nRF54L15 board, the PDM peripheral...
43 views

0 replies

Started 16 hours ago
by Cristian Turcan

Recent in the DevZone Blog

FruityMesh open sourced - Connection based meshing that will run on batteries

Marius Heil

Hello everybody, I have just published the sourcecode of FruityMesh on GitHub. It is a meshing algorithm that uses standard BLE connections. Plug in as many nodes as you like and they will automatically…
- 12 Aug 2015
Developing Nordic nRF51 Projects with Visual Studio

ivan

This tutorial shows how to create and debug a basic project for the Nordic nRF51-DK using Visual Studio. Before you begin, install VisualGDB 5.0 or later. Start Visual Studio and begin creating a new…
- 6 Aug 2015
Motor Control over BLE with nRF51822 and TB6612FNG

Mahesh Venkitachalam

In this project, we will control two motors over BLE using the Nordic nRF51-DK. To do this, we will use a motor driver based on the Toshiba TB6612FNG chip. We will use GPIOs and PWM to communicate with…
- 5 Aug 2015
Create Hurricane Tunnel Broker on Raspberry Pi

Eugene Yu

This blog introduces how to create tunnel broker service in order to support IPv6 on your IPv4 network. The tunnel broker is providing IP conversion service with 6in4. Preparation Raspberry Pi…
- 4 Aug 2015
An appeal to makers - why you should document your project, and how you can do it

Mahesh Venkitachalam

An appeal to makers - why you should document your project, and how you can do it. http://electronut.in/why-how-document-project/
- 3 Aug 2015
ADXL 345 Tutorial

Milad

Hello all, this tutorial goes to a fellow named Emil who helped me with this project. Number 1_ Make sure you set up the terminal viewer For debugging with real.You need it to see the values coming outta…
- 1 Aug 2015