Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

How can I use Central and Peripheral at the same time? 0

Hi. I am using S130 softdevice version. Basically, I am using NUS Service and make a my own NUS central service as NUS_C. It is correctly work at normal state. When...

1021 views

0 replies

Started over 9 years ago
by FormerMember
Not Answered
Reviwe for circuit using nRF51822 and Chip ANT 0

Hi All, Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf). I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
688 views

0 replies

Started over 9 years ago
by enojeon
Not Answered

nrf24l01+ how does EN_AA work in detail 0

to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet. then i thought that the settings...

536 views

0 replies

Started over 9 years ago
by thomas
Not Answered
Setting "Custom Data" in nRF51-ble-bcast-mesh 0

I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
- advertising
- s110
- nrf51422
- bluetooth low energy
- mesh
- broadcast
- keil
- nrf51822
1633 views

0 replies

Started over 9 years ago
by Ankit
Not Answered
c99 option and C++ Keil 0

Hello, I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
- c99 cpp libraries keil
2329 views

0 replies

Started over 9 years ago
by Antonio

Recent in Nordic blog

Debugging with Real Time Terminal

FormerMember

In SDK 12.0.0 or later, logging/debugging over RTT is built in to the logger module NRF_LOG. To enable logging over RTT, "check" the NRF_LOG_BACKEND_SERIAL_USES_RTT option in sdk_config.h in the configuration…
- 8 Apr 2015
Accessing the BLE mesh via the particle.io (spark.io) cloud

David Edwin

Hello. I was spending the last few days to implement an interface to access the BLE mesh via the Internet. The mesh consists of devices with LEDs, which then could be turned on and off in my browser.…
- 1 Apr 2015
How to use the latest Keil 5 for Keil 4 projects (.uvproj)

Stefan Birnir Sverrisson

As many have noticed, Keil 5 does not have native support for Keil 4 projects (project files ending with uvproj), it only has native support for Keil 5 projects (project files ending with uvprojx). However…
- 26 Mar 2015

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019