Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
nRF8001 pairing with custom key or OOB 0

Hello, I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
- pairing
- nrf8001
- key
1011 views

0 replies

Started over 10 years ago
by bgun
Not Answered
how to config the parameter of GZP_TX_RX_TRANS_DELAY? 0

i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now, is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
- nrf51822 nrf24lu1
663 views

0 replies

Started over 10 years ago
by herman
Not Answered
Long writes from S120; how to? 0

I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
- nrf58122 s120 long_write
1044 views

0 replies

Started over 10 years ago
by Michael Gauland
Not Answered

Example for combined HID/UART XML (nRF8001-Arduino) 0

Hi all, I have been trying to combine the UART and hID Keyboard examples into a single application. I want to use the HID part to send specific keystrokes using buttons...

1076 views

0 replies

Started over 10 years ago
by Bo
Not Answered
restrict which masters can pair to device 0

Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
- rf8001 ble
659 views

0 replies

Started over 10 years ago
by andrewjfox

Recent in Nordic blog

The S132 v5.1.0 is now production tested on nRF52810

Petter Myhre

This blog describes how you can setup a Segger Embedded Studio example for PCA10040E (emulating nRF52810) from nRF5 SDK 14.2 to use S132 v5.1.0, instead of S112. The procedure should be similar for the…
- 12 Sep 2018
Adding custom commands to a BLE example using Nordic UART Service

Håvard

A common thing to do is to use the Nordic UART Service for quick prototyping. Often the example itself is used as a starting point (ble_app_uart). But sometimes we use other starting points, and want to…
- 6 Sep 2018
Using Two-Factor Authentication (2FA) with the Nordic DevZone

esivertsen

Did you know you can use two-factor authentication to enhance the security of your DevZone account? In this little blog, I’ll show you how to enable Two-Factor Authentication (2FA) with your DevZone account…
- 30 Aug 2018
Introduction of SDH and SDK v15.0 software architecture

Amos Lin

The SDK software architecture has been hugely changed since SDK v13.0. With adding SDH to SDK, it provides SDH API to Enabling the SoftDevice and its event interrupt. Disabling the SoftDevice. Receiving…
- 13 Aug 2018
Bluetooth pairing vulnerability

PaKa

The Bluetooth SIG released an errata for the 4.2 and 5.0 versions of Bluetooth specification on July 23rd relating to a potential vulnerability with the pairing procedures. For Bluetooth low energy; this…
- 27 Jul 2018
Getting Started with the Thingy:52 and GCC/GDB

Daniel Veilleux

The Thingy:52 IoT Sensor Kit is a fancy development board that combines the nRF52832 SoC, a handful of sensors and user interface components, and a rechargeable battery. Although the Thingy is available…
- 20 Jul 2018