Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered
how to config the parameter of GZP_TX_RX_TRANS_DELAY? 0

i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now, is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
- nrf51822 nrf24lu1
635 views

0 replies

Started over 10 years ago
by herman
Not Answered
Long writes from S120; how to? 0

I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
- nrf58122 s120 long_write
1012 views

0 replies

Started over 10 years ago
by Michael Gauland
Not Answered

Example for combined HID/UART XML (nRF8001-Arduino) 0

Hi all, I have been trying to combine the UART and hID Keyboard examples into a single application. I want to use the HID part to send specific keystrokes using buttons...

1047 views

0 replies

Started over 10 years ago
by Bo
Not Answered
restrict which masters can pair to device 0

Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
- rf8001 ble
636 views

0 replies

Started over 10 years ago
by andrewjfox
Not Answered

nRF Beacon build problems using Eclipse Luna 0

I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...

1403 views

0 replies

Started over 10 years ago
by fmc

Recent in Nordic blog

Nordic Semiconductor nRF51822 Firmware for Background Data Recording

scytulip

#Nordic Semiconductor nRF51822 Firmware for Background Data Recording Updating on https://github.com/scytulip/nrf51-back-rec Design Objective This firmware is designed for low-cost long-time low-power…
- 23 Oct 2014
Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019