Nordic DevZone

Recent and unreplied - Help your fellow developer and earn points!

Not Answered

Central App stuck after service discovery 0

I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples. I've modified them to run on the PCA10001...

752 views

0 replies

Started over 10 years ago
by Erik Sanchez
Not Answered

nRF51822 RX device can't receive packet from nRF24L01P TX device 0

Hi All, I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device. nRF24L01P TX device Register settings are as follows; Reg.EN_AA=0x00...

650 views

0 replies

Started over 10 years ago
by Mike
Not Answered
S130 programming for the nRF51822 mkit with gcc on a raspberry pi 0

I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
1081 views

0 replies

Started over 10 years ago
by Jimi Cullen
Not Answered
MCP does not start 0

I'm using the nRF51822 eval kit I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working In nRFgo Studio / Device manager pane...
- nrf51822 mcp
562 views

0 replies

Started over 10 years ago
by swjdaenen
Not Answered
SERVER: Write Command on handle 0003, failed 0

the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding. 476;16:12...
- proximity example
529 views

0 replies

Started over 10 years ago
by jerry dzoleko

Recent in Nordic blog

Nordic nRF51822 ARM Cortex-M0 Development using emIDE

Hugh

Nordic nRF51822 ARM Cortex-M0 Development using emIDE To avoid the hefty charges with commercial compilers I tried emIDE with some success; here are the settings I used for the EV Kit Official emIDE…
- 22 Oct 2014
Beacon Kit - Mistake in Ref_Design_UG_v1.0

Salman

I connected the programming header as described in "nRF6930_Beacon_Ref_Design_UG_v1.0.pdf" 5.5.4 Programming interface. I was trying to program Beacon Kit but failed many times then I compared it with…
- 10 Oct 2014
SD card interfacing

Salman

Hi, I have written SD & SDHC card routine for reading, writing and erasing data from SD card. It used the hardware SPI of nRF51822. NOTE: 1)Define the PINs of SD card first before initialing. 2)Define…
- 10 Oct 2014

Latest guides

Getting started: nRF Connect for Cloud Certificate Update

Joakim

The content of this guide is now covered in the documentation on nrf Connect SDK documentation page.For the most up-to-date instruction to Update Cloud Certificate please follow this link.
- 27 Sep 2019
Getting started: Thingy:91 Firmware Update using MCUboot

Joakim

The nRF Connect Programmer application now also supports MCUboot! Follow these steps to update through the programmer application or the following guide for the command line alternative. This guide shows…
- 23 Sep 2019
Bluetooth low energy: Concurrent Advertising

Håvard

I have been asked several times about variations of the following advertising scenario, so I decided to make a blog post that I can refer to, and hope it might prove useful for others out there that are…
- 9 Sep 2019
Software and Protocols: The four kinds of data you need to consider when developing an IoT product

Markus Tacker (he/him)

In this post I will give you an introduction to the four kinds of data you need to consider when developing an IoT product: Device State Device Configuration Past Data Firmware Updates It's these …
- 9 Sep 2019
Getting Started : Automate building of HEX files for your nRF Connect SDK application using CircleCI or GitHub Actions

Markus Tacker (he/him)

Continuous delivery is in important aspect of short time to market and since the nRF9160 supports firmware over the air updates we want to ship a new firmware to our development boards every time we update…
- 14 Aug 2019
nRF5x: Automating Power Profiler Kit measurements from the command line

Daniel Veilleux

Nordic's Power Profiler Kit (PPK) is an inexpensive piece of hardware that can provide a significant amount of insight into the operation and performance of your project. Although there is a lot that…
- 2 Aug 2019